Compact Power BOXER 118 Скачать руководство пользователя страница 83

Страница: 83 / 88

5-3

Troubleshooting

The machine does not
travel in either forward or
reverse directions.

• Engine is not running at full

speed.

• Advance throttle to full engine

speed.

• Hydraulic fluid is cold.

• Fully warm hydraulic fluid.

• Hydraulic fluid level is low.

• Check and fill the hydraulic

fluid tank with the appropriate
hydraulic fluid.

• Fuel tank is empty and engine

stops.

• Fill fuel tank with fuel.

• If all above has been checked.

• Contact authorized service

dealer.

Trencher chain does not
turn

• Trencher control lever not in the

proper position.

• Move trencher control lever in

the activation position.

• Operator presence control not

depressed.

• Depress (step on) operator

presence control.

• Engine not at rated speed.

• Move throttle to maximum

RPM setting.

• Power unit is low on hydraulic

fluid.

• Refer to power units

Operator's Manual

• Trencher Chain drive motor is

leaking hydraulic fluid.

• Replace hydraulic auger

drive motor.

Trencher Chain rotates,
but not smoothly or stops
and starts.

• Soil may contain rocks or other

items that are preventing
smooth operation.

• Raise trencher chain from the

trench to clear contact with
the obstruction.

• Power unit is low on hydraulic

fluid.

• Check and fill the hydraulic

fluid tank with the appropriate
hydraulic fluid.

• Trencher hydraulic drive motor

is failing.

• Replace hydraulic drive

motor.

Hydraulic drive motor is
turning but the spoils
auger does not move

• Spoils auger connection bolt not

installed.

• Install and secure connection

bolt.

• Spoils auger connection bolt

has sheared off.

• Install and secure connection

bolt.

Hydraulic fluid is leaking
from trencher drive
motor.

• Hydraulic fitting loose.

• Tighten hydraulic fittings.

• Internal hydraulic motor seals

leaking.

• Replace hydraulic drive

motor.

Engine starts but does
not continue to run when
using trencher.

• Too much downward force is

being applied to trencher,
stalling engine.

• Raise trencher slightly.

• Power unit low on fuel.

• Refuel power unit.

Poor trencher
performance, does not
penetrate soil easily.

• Worn trencher chain teeth.

• Replace worn trencher teeth

• Not enough down pressure on

trencher.

• Increase downward pressure

on the trencher.

Problem

Possible Causes

Corrective Action

Содержание BOXER 118

























































































Результаты поиска

Содержание BOXER 118

Отзывы:

Бренды по названию

Популярные бренды

Compact Power BOXER 118, Руководство оператора

Результаты поиска

Содержание BOXER 118

Отзывы:

Бренды по названию

Популярные бренды