manualshive.com logo in svg

Compact Power BOXER 118, Руководство оператора

Поделиться
Скачать
Compact Power BOXER 118 Скачать руководство пользователя страница 18

1-4

Safety Precautions

SERVICE & MAINTENANCE SAFETY 

Maintenance work can be hazardous if not done in a careful manner. All personnel should 
realize the hazards and strictly follow safe maintenance practices. Failure to comply with these 
safety precautions may result in serious personal injury and/or death. 

•

Use only BOXER supplied or approved replacement parts. Imitation parts may lead to unit 
damage and/or injury to personnel. Warranty may be voided if unauthorized parts and are 
used.

•

Wear the proper protective clothing and personal safety equipment necessary to perform the 
maintenance or service required.

•

Keep the machine free of grass, leaves, or other debris build-up.

•

Clean up oil or fuel spillage.

Fuel or oil leaks or spills can create a fire or explosion hazard.

•

Prior to performing maintenance or service, park the unit in a level area away from 
obstructions and/or work site hazards.

•

Be sure the area has adequate light and is well ventilated. NEVER operate the machine 
inside a closed area.

•

Clean-up any oil, grease, mud, water, or snow which might cause the floor surface to become 
slippery.

•

If the machine requires maintenance, take the machine out of service and attach a "Do Not 
Operate" tag at the control panel and remove the ignition key.

•

If maintenance or repairs require the boom to be raised, securely support the boom.

•

Know where all pinch points and rotating parts on the unit are. These areas must be avoided 
to prevent serious injury.

•

Remove only those guards or covers on the component being serviced and replace them 
immediately upon completion of the work.

•

Never attempt to adjust or service engine or machine components while they are hot.

ELECTRICAL SYSTEM HAZARDS 

•

Prior to working on the electrical system: 
– Disconnect battery cables, removing the battery ground cable first. 
– When re-connecting the battery, connect the battery ground cable last. 
– Never allow battery cables to contact hydraulic lines or rub against sharp edges. 

WARNING

Содержание BOXER 118

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды