Comnet NetWave NW7 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 70

background image

INS_NW7[E]_REV– 06/10/13 PAGE 41

INSTALLATION AND OPERATION MANUAL

NW7[E]

TECH SUPPORT: 1.888.678.9427

11.2.2 DHCP Server

This section allows you to configure the device as a DHCP server.

General Setup

Ignore
interface

Disables DHCP for this interface. You should uncheck this to enable DHCP.

Note: All the following options in this DHCP Server section depend on DHCP being enabled.

Start

Specifies the lowest leased address as offset from the network address, the default
being 100.

Limit

Sets the maximum number of leased addresses, the default being 150.

Lease Time

States the expiry time of leased addresses, the default being 12h.

Advanced Settings

Dynamic DHCP Dynamically allocates DHCP addresses for clients. If disabled, only clients having static

leases will be served. Checked by default.

Force

Forces DHCP on this network even if another server is detected, unchecked by default.

IPv4-Netmask

Overrides the netmask sent to clients. Normally it is calculated from the subnet that is
served.

DHCP-Options Defines additional DHCP options, for example "6,192.168.10.1,192.168.10.2" which

advertises different DNS servers to clients. Normally, connected devices would take
this board's IP address as the default gateway. To set an alternative default gateway,
add the DHCP option "3,192.168.10.3" for example.

11.2.3 Static Leases

In this section, you can specify that a particular DHCP client obtain an IP address that you define.
The MAC address of the client is required. Click the Add button to add a static DHCP lease, then
click Save & Apply to apply the changes.

Figure 35: Adding a static DHCP lease.

«
...
39
40
41
42
43
...
»

Содержание NetWave NW7







































































Отзывы:

Нет отзывов

Похожие инструкции для NetWave NW7

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 66

Бренд: Pathport Страницы: 3

SR6602-I AI Series

Бренд: H3C Страницы: 29

Air Live SG-101

Бренд: Ovislink Страницы: 18

Бренд: RTA Страницы: 76

Бренд: Cell2Tel Страницы: 34

Бренд: Avid Technology Страницы: 152

Бренд: ioLIVING Страницы: 3

Бренд: Technicolor Страницы: 12

Intelligent Gateway 1800

Бренд: 2Wire Страницы: 148

Бренд: ZyXEL Communications Страницы: 2

Wireless DSL Gateway GT704WG-QW04

Бренд: ActionTec Страницы: 97

Бренд: Deco Страницы: 22

Бренд: Cabletime Страницы: 16

Бренд: Rosslare Страницы: 28

Бренд: Rosslare Страницы: 52

Бренд: Weiser Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды