background image

INS_FVT110/BO_REV–

2/15/12

PAGE 4

INSTALLATION AND OPERATION MANUAL 

FVT110(M,S)1/BO

FIGURE 3 – BIPHASE DATA SWITCH POSITIONS (FVR110)

The mode for each data channel is configured using a pair of switches on the front panel of the receiver unit. The 2 position CC Contact Switch is not used 
when connected to an FVT110/BO in-dome module.

FIGURE 4 – DATA CONNECTIONS

Switch

1                 2

GND  

DIN (–) 

DIN (+) 

DOUT (–) 

DOUT (+)

Bi-phase

DOUT(+)

DOUT(–)

DIN(+)

DIN(–)

Data In (+)

Data In (–)

Data Out (+)

Data Out (–)

Customer

Equipment

Customer

Equipment

UTC Control

FVT110/BO

FVT110/BO

Customer

Equipment

Customer

Equipment

FVR110

FVR110

Up-the-Coax

Control Receiver

VIDEO IN

VIDEO OUT

Up-the-Coax  

Control Transmitter

© 2012 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet logo” are registered trademarks of Communication Networks, llC. 

3 cORPORATE DRIVE | DANBURy, cT 06810 | USA 

T: 203.796.5300 | F: 203.796.5303 | TEch SUPPORT: 1.888.678.9427 | [email protected]

8 TURNBERRy PARK ROAD | GILDERSOME | MORLEy | LEEDS, UK LS27 7LE

T: +44 (0)113 307 6400 | F: +44 (0)113 253 7462 | [email protected]

INSTALLATION cONSIDERATIONS 

This fiber-optic link is supplied as an in-dome module. Units should be installed in dry locations protected from extremes of temperature and humidity.

cAUTION:

 

Take care not to press on any of the LEDs.

IMPORTANT SAFEGUARDS: 

A)  Elevated Operating Ambient

 - Consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature 

(Tma) specified by the manufacturer.

B)  Reduced Air Flow

 - Installation of the equipment should be such that the amount of air flow required for safe operation 

of the equipment is not compromised.

Содержание FVT110M1/BO

Страница 1: ... one single mode or multimode optical fiber The FVT110 BO in dome module supports Bosch Bilinx up the coax camera control over its entire specified fiber distance The series features a unique time base correction algorithm that removes the usual distance limitations associated with up the coax control Bi color Red Green LED indicators are provided for rapidly ascertaining equipment operating statu...

Страница 2: ...connector with white plastic shroud with Bosch s 5 pin to 8 pin cable assembly Video LED D1 should illuminate red Data LED D2 should stay off Link LED D3 should illuminate red 3 Connect video to module at J4 2 pin male connector with white plastic backing with ComNet s 2 pin to BNC cable connecting the other end to the Dome BNC Video LED D1 should illuminate green 4 Connect Single mode or Multimod...

Страница 3: ...o control the camera then connect data to screw terminal block on module Biphase CODE should be connected to DIN Biphase CODE should be connected to DIN Shield should be connected to GND NOTE LINK LED will illuminate green once a link is established over optical fiber with the In Dome Transmitter module VIDEO LED will illuminate green when active signal is detected at the BNC DATA LED will flash g...

Страница 4: ...ed ComNet and the ComNet Logo are registered trademarks of Communication Networks LLC 3 Corporate Drive Danbury CT 06810 USA T 203 796 5300 F 203 796 5303 Tech Support 1 888 678 9427 info comnet net 8 Turnberry Park Road Gildersome Morley Leeds UK LS27 7LE T 44 0 113 307 6400 F 44 0 113 253 7462 info Europe comnet net Installation Considerations This fiber optic link is supplied as an in dome modu...

Отзывы: