CommScope PFU-12-C-O-060-01 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 36

CommScope PFU-12-C-O-060-01 Скачать руководство пользователя страница 17

PoE Extender Hardware Manual

This product is copyright © 2019 CommScope, LLC. All Rights Reserved.

13

3. Installation

Installation of the PoE Extender should be completed in the following order.

Remove Heat Shield

Remove the 4 bolts attaching the heat shield to the PoE Extender with a 3mm Allen key. Slide the

heat shield off the retaining lugs and put to one side.

Remove Seal Caps and Grommets

The Two-port PoE Extender has 2 x M25 and 1 x M20 cable glands 60W
The Single-port PoE Extender has 1 x M25 and 1 x M20 cable gland
Power Extenders have 3 x M20 cable glands.
Unscrew the caps and then remove the grommets from all of the pass-through connectors.

Note 1:

Do not

unscrew the pass-throughs from metal body of the extender. These have been

factory fitted and sealed to the correct torque setting.

«
...
15
16
17
18
19
...
»

Содержание PFU-12-C-O-060-01





































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды