CommFront DVS-232-2 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 49

CommFront DVS-232-2 Скачать руководство пользователя страница 8

1.0 Introduction

CommFront User Manual

7

1.4.3 Modbus Gateway

Modbus RTU is the most widely used industrial protocol. A typical Modbus system

consists of one master and multiple slaves that run over the same single twisted pair

cable. The DVS-232-2 can act as a Modbus gateway that encapsulates Modbus

packets in standard TCP/IP packets. This enables the filed Modbus devices to connect

and communicate over existing Ethernet and fiber networks instantly. In addition,

conventional Modbus RTU has a limitation of 247 nodes per network, while Modbus

TCP networks can have as many slaves as the physical layer can handle, which often

go around 1,024.

APPLICATION 3: MODBUS GATEWAY

1.4.4 Modbus Protocol Converter

The DVS-232-2 can act as a Modbus protocol converter that encapsulates Modbus

packets in standard TCP/IP packets. A Modbus protocol converter allows conventional

Modbus RTU master and slave devices that run on twisted-pair cable to run over

Ethernet and fiber networks with greater distance and flexibility (e.g. the COM port

settings for client and server can be different).

APPLICATION 4: MODBUS PROTOCOL CONVERTER

«
...
6
7
8
9
10
...
»

Содержание DVS-232-2


















































Отзывы:

Нет отзывов