Commend GE 800 Скачать руководство пользователя страница 34

Страница: 34 / 43

Technical data

GE 800

4.2/0617

Processor card G8-GEP

Processor card with Blackfin DSP, flash for basic operating system and features, signal-LED for status
and diagnosis.

Networking card G8-NET

Fully digital IP networking card with 2 IP Ethernet ports and one digital data ring, incl. connection cable
and 4 signal LEDs for status and diagnosis.

Operating temperature range

0 °C to +50 °C (32 °F to 122 °F)

Storage temperature range

–30 °C to +60 °C (–22 °F to 140 °F)

Relative humidity

20% up to 80%, not condensing

Plug

96-way PC board connector according DIN 41612

Power supply

via Intercom Server

Emergency power consumption

see GE 800 above

Dimensions

100 x 167 mm (3.9 x 6.6 in)

Weight

approx. 230 g (0.51 lbs)

Flash memory

8 MB

RAM memory

2 MB

Operating temperature range

0 °C to +50 °C (32 °F to 122 °F)

Storage temperature range

–30 °C to +60 °C (–22 °F to 140 °F)

Relative humidity

20% up to 80%, not condensing

Plug

165-pin connector

Power supply

via Intercom Server

Emergency power consumption

see GE 800 above

Dimensions

100 x 167 mm (3.9 x 6.6 in)

Weight

approx. 325 g (0.72 lbs)

Number of conversations between two GE 800

Maximum cable length between two GE 800 (IP)

100 m (328 ft)

Maximum cable length between GE 800 and
GE 700 (GEV)

5 m (16.4 ft)

Cable type

standard Cat. 5 cables with RJ45 jacks

Содержание GE 800












































Результаты поиска

Содержание GE 800

Отзывы:

Похожие инструкции для GE 800

Бренды по названию

Популярные бренды

Commend GE 800, Руководство по эксплуатации продукта

Результаты поиска

Содержание GE 800

Отзывы:

Похожие инструкции для GE 800

Бренды по названию

Популярные бренды