background image

3

3

www.comfortzoneproducts.com

USAGE 

Fan operation: 

Always operate the fan in the upright position 

following all instructions and recommendations listed in this 
manual. 

Fan location: 

Place the fan in the area of the room that will 

provide proper fan cooling. 

Fan connection: 

Plug fan directly into 120 volt A.C., 60Hz wall 

outlet. Be sure plug fits tightly in outlet. A loose connection may 
cause overheating and damage to the plug or fan. 

Note: 

To prevent overloading a circuit, do not plug the fan into a 

circuit that is servicing other electrical needs. 

Speed Control: 

While facing the fan, pull the 

right string

 for 

speed setting. The fan will cycle through the following speed 
settings: 

OFF, LOW, HIGH, OFF. 

Oscillation Control: 

Pull the 

left string 

for oscillation. 

To Adjust Airflow Upward or Downward: 

Loosen the 

position screw first and then loosen the pivot nut. Tilt motor to 
the desired angle then firmly tighten the pivot nut first and then 
tighten the position screw. 

INSTALLATION INSTRUCTIONS

The wall fan must be mounted on 12 inch (300mm) thick dry and 
cement-grouted firm wall or on 4 by 5 inch wood studs/joists. Use 
wall bracket as a template for locating the holes to be drilled.

After determining the hole locations, drill holes through mounting 
surface using an appropriate sized drill bit. 
It is recommended that a minimum of grade 5 fasteners be used. 
The following are acceptable surfaces for mounting wall mount 
assembly. 

STEEL SURFACE

 - When mounting to a steel surface, such as 

vertical I-beam, drill through holes at pre-marked locations using 
a 9/32" drill bit. Attach wall mount assembly to mounting surface 
using 1/4"-20 hex screw, in combination with 1/4" flat washers, 
1/4" lock washers, and 1/4"-20 hex nuts.

MASONRY SURFACE

 - When mounting to a masonry surface 

use a 1/4" expansion type bolt or 1/4" masonry lag with shield. 
Drill holes at pre-marked locations using appropriate sized drill 
bit as recommended for fastener.

NOTE:

 HARDWARE NOT SUPPLIED

DO NOT

 

operate any fan with a damaged cord or plug or after 

fan malfunctions, has been dropped or damaged in any manner. 

Do not operate fan with a broken blade, safety cage or any visual 

imperfections. Disconnect power before servicing.  For repairs 

covered under warranty, see warranty statement. For all other 

repairs contact Comfort Zone

®

 Customer Service by telephone or 

mail for information and assistance. 

DO NOT

 

run power cord under carpeting. DO NOT cover cord 

with throw rugs, runners or the like. Arrange cord away from 

traffic area where it will not be tripped over. Avoid the use of 

extension cords due to risk of fire. If an extension cord must 

be used, the cord must be minimum 14 AWG and rated not 

less then 1875 watts. Do not use an extension cord unless the 

plug can be completely inserted into its receptacle. Unplug 

the fan when not in use. Do not operate fan with its ventilation 

obstructed. 

WARNING:

 TO REDUCE THE RISK OF FIRE, 

ELECTRIC, SHOCK, OR INJURY TO PERSONS, 

OBSERVE THE FOLLOWING:  

a) Installation work and electrical wiring must be done by 

qualified person(s) in accordance with all applicable codes 

and standards, including fire-rated construction. 

b) When cutting or drilling into wall or ceiling, do not damage 

electrical wiring and other hidden utilities.

ASSEMBLY INSTRUCTIONS 

1. Install the wall bracket following Installation Instructions.
2. Install the fan motor on the angle support bracket.
3. Assembling the back guard, blade, front guard to the motor.

SPECIFICATIONS 

  Voltage  Frequency 

Wattage 

Max.  

Recommended  

 

 

 

Low            High 

Amperage  Extension Cord Gauge

 

  120 V 

60 Hz  185 W    230 W  1.8 A 

16 AWG

Содержание CZHVW30EX Series

Страница 1: ...ructions CZHVW30EX Series 30 Oscillating Wall Mounted Fan Features 2 Speed Industrial Fan Individually Balanced Aluminium Blade All Metal Body Steel Safety Grilles 2 Pull Strings for Power and Speed Control for Oscillation Control 120V A C 60Hz ...

Страница 2: ...equate consult a qualified electrician While using your fan you should follow the IMPORTANT INSTRUCTIONS listed below As part of those instructions we have used the word WARNING to indicate the level of hazard WARNING indicates a hazard which if not avoided could result in injury or death IMPORTANT INSTRUCTIONS As with all electrical appliances basic safety precautions should always be followed to...

Страница 3: ... 1 4 lock washers and 1 4 20 hex nuts MASONRY SURFACE When mounting to a masonry surface use a 1 4 expansion type bolt or 1 4 masonry lag with shield Drill holes at pre marked locations using appropriate sized drill bit as recommended for fastener NOTE HARDWARE NOT SUPPLIED DO NOT operate any fan with a damaged cord or plug or after fan malfunctions has been dropped or damaged in any manner Do not...

Страница 4: ...2 5 or 5 0 Amp 125 Volt fuse 3 6mm x 10mm Be sure fuse is properly seated within its cavity 5 Close fuse cover by sliding it back to its original closed position Fig 1 Fig 2 Fig 3 Slide Cover to Open LIMITED WARRANTY This unit is guaranteed to the original retail purchaser against defects in quality or workmanship for a period of one year from the date of original purchase If this unit fails becau...

Отзывы: