background image

6

6

www.comfortzoneproducts.com

Figure 7

WARNING: 

It is advised that at the start of each heater season, 

the power should be turned off at the circuit breaker and the 
LI & L3 lug screws checked for tightness and 

proper torque

The heater should be cleaned and checked for mechanical and 
electrical integrity. See 

SPECIFICATIONS

 and NEC/local codes.

ADJUSTING AIR FLOW:

 

1. 

 Tilt the unit

- Loosen the top Small Knob-Screws and thread  

 

into provided holes in heater until tight. See 

Figure 5

.

2.

   Adjust the louvers

 in front of the heater as desired. See 

 

Figure 5

.

NOTE:

 DO NO OPERATE THE HEATER WITH THE FRONT  

LOUVERS CLOSED, DAMAGE TO THE HEATER COULD  
RESULT.

SAFETY INSTRUCTIONS:

To start the heater, turn on the circuit breaker. The Power 
Indicator light will light up to indicate there is power available. 
Press the POWER button to turn the heater on. The heater will be 
in HIGH setting by default. The heater indicator will illuminate, and 
the LED display will show the default setting temperature 80°F. 

1.  The heater is HOT when in use. Do not let bare skin touch any  
 

hot surfaces.

2.  Keep combustible materials (furniture, pillows, bedding,    
 

papers, clothes, curtains, and similar items) at least 3  

 

 

feet (0.9m) from all sides and surfaces of the heater.

3.  Do not use outdoors or in wet areas like bathrooms, laundry  
 

areas or where it could fall into a swimming pool or other 

 

container of water.

4.  This heater is a 240V AC rated direct wired appliance. Never  
 

use extension cords or relocatable power taps.

CARE AND MAINTENANCE:

CLEANING THE HEATER

:

1.  Do not disassemble the heater to clean it.
2.  The heater should be powered OFF and disconnected from  
 

the power at the circuit breaker before attempting to clean   

 

any portion of the heater.

3.  The exterior can be cleaned with a cloth, brush and/or  
 vacuum.
4.  The louvers, fan blade and heating element are delicate and  
 

should not encounter hard items. They can be cleaned by    

 

brush, vacuum and mild compressed air.

MAINTENANCE: 

This Industrial Heater contains no user serviceable parts.
In the unlikely event that your heater should need service, please 
contact: World and Main (Cranbury), LLC 324A Half Acre Rd. 
Cranbury, NJ 08512 USA 800-221-6895  
www.comfortzoneproducts.com

Содержание CZ260ER Series









Отзывы: