3
3
www.comfortzoneproducts.com
USAGE:
FAN OPERATION:
Always operate the fan in the upright
position following all instructions and recommendations listed
in this manual.
FAN LOCATION:
Place the fan in the area of the
room that will provide proper fan cooling.
FAN CONNECTION:
Plug fan directly into 120 Volt A.C., 60Hz wall outlet. Be sure plug
fits tightly in outlet. A loose connection may cause overheating
and damage to the plug or fan.
NOTE:
To prevent overloading
a circuit, do not plug the fan into a circuit that is servicing other
electrical needs.
TURNING FAN ON:
With fan mounted to a stable wall surface,
plug fan into properly functioning outlet. To start the fan, press
SPEED/ON button. Press SPEED/ON repeatedly to desired
fan speed ‑ HIGH, MID, LOW. Press OFF button to discontinue
use. Unplug fan when not in use.
OSCILLATION:
To start fan oscillation, press OSC button on
the control panel or remote control while fan is at any speed or
mode. To discontinue oscillation, press the OSC button on
control panel or remote control again.
ADJUSTING FAN TILT:
To adjust the tilt angle simply tilt the fan
to desired position. Ratcheting effect should hold the fan at the
desired angle.
REMOTE CONTROL:
Place 2 ea. AAA size batteries (not
included) in the remote control. Use the buttons on the remote
as you would with the control panel. Point the remote control
towards the control panel for the sensor to receive a signal.
NOTE:
All batteries should be replaced at the same time, do not
mix with old batteries. Do not mix alkaline, standard (carbon‑zinc)
or rechargeable (nickel‑cadmium) batteries. Properly dispose of
used batteries.
TIMER FEATURE:
Accessed using the remote control, the timer
function is designed to work during oscillation or any fan mode
or speed. Press the TIMER button, each time it is pressed, time
duration indicator lights illuminate. (0.5, 1, 2 or 4 hours). Simply
add up the time value of the lights to see timer setting up to
7.5 hours maximum time. To turn the TIMER function off, press
the TIMER button continuously until all the timer indicator lights
are off.
FAN MODES:
Accessed using the remote control, this fan has
three operating modes that will work with oscillation control
ON or OFF.
1.
NORMAL
– Fan speed is consistent with the speed chosen
and operates like a standard fan.
2.
PULSE
– Fan will vary the speed from the highest fan speed
chosen to very slow speed.
3.
SLEEP
– Fan will vary the fan speed like pulse mode but it
ASSEMBLY
INSTRUCTIONS:
Images may vary slightly from
actual product.
STEP 1:
Remove the Blade Cap by
twisting it CLOCKWISE while
holding the metal shaft tightly.
NOTE:
Threads are reversed.
Unscrew = Clockwise
.
STEP 2:
Assemble Rear Grille onto
Motor Housing. Rear Grille
should fit into pins on fan
motor housing as shown.
STEP 3:
Thread Locknut onto Motor
Housing to lock Rear Grille
in place.
STEP 4:
Remove any protective
covering over shaft before Fan
Blade installation. Place Fan
Blade onto Motor Shaft. Notice
the pin on Motor Shaft should
fit into slots of Fan Blade.
STEP 5:
Thread Blade Cap onto
threaded end of Motor Shaft.
NOTE:
Threads are reversed.
Tighten = Counter-clockwise
.
STEP 6:
Attach Front Grille to Rear
Grille with Hook Clip centered
on the top above Wire Handle.
Pin
Pin
Pin
Slot
Hook Clip
Loosen
Blade Cap
Tighten
Locknut
Control Panel
USAGE:
(cont.)
is timed to slow down after a period of time. The speed will
change as follows:
FAN HIGH SPEED
– When fan speed is set to HIGH, the fan
will run varying from HIGH speed to very slow speed for 30
minutes, then run from MEDIUM to very slow speed for 30
minutes, then run from LOW speed to very slow speed for the
duration of use.
FAN MEDIUM SPEED
– When fan speed is set to Medium, the
fan will run varying from MEDIUM speed to very slow speed
for 30 minutes, then run from LOW speed to very slow speed
for the duration of use.
FAN LOW SPEED
– When fan speed is set to LOW, the fan will
vary from LOW speed to very low speed for the duration of use.
