CB081A-CB143A / CBE103A-CBE143A Series
Installation and Operation Instruction Manual
11
www.coastair-ac.com
Owner’s Manual -
Room Air Conditioner with R-410A BG-P/BG-M/BGE-M Series
10
Owner’s Manual
Room Air Conditioner with R-410A
Heat Controller
11
INSTALLATION INSTRUCTIONS
W a l l S l e e v e B r a n d s :
# 4 G e n e r a l E l e c t r
ic
/ H o t p o i n t 1 6 D e e p
1 . R e m o v e e x i s t i n g r e a r g r i l l e a s s h o w n o n P a g e
6 o f t h i s m a n u a l a n d r e p l a c e w i t h p r o v i d e d
l o u v e r e d r e a r p a n e l . I n s t a l l a s s h o w n h e r e .
N O T E :
Yo u m a y n e e d t o d r i l l h o l e s i n f l a n g e o f
e x i s t i n g s l e e v e t o m a t c h n e w r e a r g r i l l e .
7
8
/
2 .
C u t ( 2 ) 1 7 Ta p e r e d S p a c e r B l o c k s a s s h o w n
b e l o w i n t o t w o p i e c e s .
3 . I n s t a l l 1 3 s e c t i o n a s s h o w n w i t h t h e t a p e r e d e n d
f r o m t h e b a c k o f t h e s l e e v e . T h i s h e l p s i n d u c e a
r e a r w a r d s l o p o n t h e u n i t .
4 . A t t a c h ( 1 ) 1 x 3 / 8 x 2 5 l o n g s e a l i n t h e c e n t e r
a t t h e t o p o f t h e s l e e v e . R e m o v e t h e b a c k i n g
p a p e r a n d p r e s s i n t o p o s i t i o n .
5 . A t t a c h ( 2 ) 1 x 3 / 8 x 1 4 s e a l s t o t h e l e f t a n d
r i g h t s i d e s o f t h e s l e e v e .
6 . C u t ( 2 ) 1 x 3 / 8 x 2 5 l o n g s e a l s t o 1 4 l o n g
a n d a t t a c h i t t o t h e v e r t i c a l s e c t i o n s o f t h e r e a r
g r i l l e a s s h o w n .
7 . C e n t e r u n i t a n d g e n t l y s l i d e u n i t i n t o s l e e v e .
8 . B e f o r e s l i d i n g a l l - t h e - w a y b a c k , r e m o v e 2 n d
s c r e w f r o m f r o n t o n l e f t s i d e o f u n i t .
9 . R e m o v e t h e p l a s t i c w a s h e r f r o m t h e s c r e w.
1 0 . S c r e w a n d a t t a c h t h e o t h e r e n d o f t h e g r o u n d
w i r e t o t h e u n i t a s s h o w n i n p i c t u r e . M a k e s u r e
t h a t t h e t o o t h e d w a s h e r i s a g a i n s t t h e c a b i n e t .
1 1 . S l i d e t h e u n i t c o m p l e t e l y t o t h e r e a r t o e n s u r e
a g o o d s e a l , m a k i n g s u r e t h e g r o u n d w i r e d o e s
n o t b e c o m e t a n g l e d .
1
/
2
3
/
4
1 7
T a p e r e d S p a c e r B l o c k
1
P r o t e c t i o n P a p e r
B a c k i n g
C u t H e r e
1 3
5
4
4
4
4
4
3
8
3
8
1 0
3. Install 13” section as shown with the tapered end
from the back of the sleeve. This helps induce a rear-
ward slope on the unit.
4. Attach (1) 1” x 3/8” x 25” long seal in the center at the
top of the sleeve. Remove the backing paper and press
into position.
5. Attach (2) 1” x 3/8” x 14” seals to the left and right sides
of the sleeve.
6. Cut (2) 1” x 3/8” x 25” long seals to 14” long and attach it
to the vertical sections of the rear grille as shown.
7. Center unit and gently slide unit into sleeve.
8. Before sliding all-the-way back, remove 2nd screw from
front on left side of unit.
9. Remove the plastic washer from the screw.
10. Screw and attach the other end of the ground wire to
the unit as shown in picture. Make sure that the toothed
washer is against the cabinet.
11. Slide the unit completely to the rear to ensure a good
seal, making sure the ground wire does not become
tangled.
12.
Seal & Frame the unit as described on page 17.
13.
If you have difficulty with mounting the grill to the sleeve,
follow the instructions for direct mounting on Page 16.
#4 General Electric/Hotpoint - 16-7/8” Deep
1. Remove existing rear grille as shown on Page 6 of
this manual and replace with provided louvered rear
panel. Install as shown here.
NOTE:
you may need to drill holes in flange of
existing sleeve to match new rear grille.
2. Cut (2) 17” Tapered Spacer Blocks as shown
below into two pieces.
