background image

 

 

21 

5.9. 

 

Working conditions 

To ensure proper working conditions for the uninterruptible power supply system, the room with the 
power supply must be dry, clean and free of dust and dirt. 
From time to time (at least every 6 months or more often depending on the degree of soiling), clean 
the ventilation openings on the power supply to ensure free air flow. 

To extend the battery life, the ambient temperature should be between 15 and 25 ° C.

 

It is not reco

mmended to operate the UPS at temperatures outside the range of 0 ÷ 40 ° C

 

and with a humidity exceeding 95% (no condensation). 

5.10. 

 

The storage conditions 

If the UPS is not in use and storage or storage is envisaged, the batteries must be recharged periodically 
to  avoid  damaging  them.  Depending  on  the  storage  temperature,  the  power  supply  should  be 
connected at least every 6 months to charge the battery. Typically, the batteries are charged in 4 hours 
to 90% capacity, but it is recommended to leave the power supply on for 24-48 hours to fully charge 
the batteries, which will extend their life. 
 

Temp. storage up to 20 ° C 

- charging every 6 months. 

Temp. storage up to 30 ° C 

- charging every 3 months. 

Temp. 40 ° C storage 

- charging every 1 month. 

 

5.11. 

 

Battery change 

If the operating time of the UPS is halved with the batteries working properly, or the UPS reports a 
battery alarm, the batteries should be replaced immediately. 

After disconnecting the batteries, the receivers are not protected against power outages. 

 

It is not recommended to replace the batteries while the UPS and receivers are operating. 

 

It is not allowed to replace the batteries while the UPS is operating in battery mode! 

Содержание COVER CORE 10K
























Отзывы: