Comet S0541 Скачать руководство пользователя страница 9

IE-LOG-S0541-03 

 

  9 

 

Replacement procedure: 

 

switch off the logger by the PC program or by magnet (if low battery allows) 

 

unscrew four corner screws and remove the lid 

 

remove old battery by pulling the glued tape 

 

insert new battery 

respecting the correct polarity

 (see s and – near battery holder). If 

you  connect  new  battery  up  to  30  s,  all  logger  settings  remain unchanged. In the opposite case 
check by means of PC program all settings, especially the real time clock in logger. 

Attention, 

inserted battery with incorrect polarity causes logger damage!

 

 

put the lid back again and screw four screws. Be careful to have the rubber sealing properly in the 
slot and tighten the screws properly to ensure the water resistance of the instrument. 

connect  logger  to  the  computer  and 

write  to  it  the  information  on  battery  replacement 

(menu Configuration/Battery replacement). This step is necessary to evaluate properly the remaining 
battery capacity. 

 
 
 

Old battery or logger itself (after its life) is necessary to liquidate ecologically!

 

 
 
 
 
 
 
 

Connection of female ELKA 3008V connector for temperature probe and voltage contact 

It  is  possible  to  order  as  an  optional  accessory  connector  for 

connection of temperature probe. Signal cable should be shielded, round 
cross section of minimum diameter of 3.5 mm and maximum diameter of 
5 mm, maximum length of 10 m and as large as possible cross section of 
cords  (stranded  wires).  Outer  diameter  must  be  from  1  to  1.55  mm 
including  insulation.  Connect  connector  to  temperature  signal 
accordingly  to  the  figure  by  means  of  the  manual  included  in  delivery. 
Choose  the  most  suitable  plastic  insert  accordingly  to  the  diameter  of 
stranded  wires  of  the  cable.  The  IP67  protection  is  guaranteed  only  if 
connector is assembled correctly! 

It  is  necessary  to  select  and  connect  cable  for  voltage  inputs  with 

respecting the same rules as above. Connect the voltage signals instead of the RTD probe. Connect 
positive pole to the brown terminal and signal ground to the blue terminal. Due to high impedance 
of  voltage  inputs  it  is  necessary  to  avoid  places  with  higher  electromagnetic  interference  when 
installing cables from contacts (switchboards, motors, contactors, frequency converters, etc.). 

 
 

Instrument passed through tests of electromagnetic compatibility (EMC): 

 

Device conforms in accordance with EN 61326-1 these norms: 

 

radiation:  

EN 55011 Class B 

 

immunity:  

EN 61000-4-2 (levels 4/8 kV, Class A) 

 

 

 

EN 61000-4-3 (intensity of electric field 3 V/m, Class A) 

 

 

 

EN 61000-4-4 (levels 1/0.5 kV, Class A) 

 

 

 

EN 61000-4-6 (intensity of electric field 3 V/m, Class A) 

 

Содержание S0541










Отзывы: