manualshive.com logo in svg

Comet System T0610, Руководство пользователя

Поделиться
Скачать
Comet System T0610 Скачать руководство пользователя страница 33

IE-SNC-Tx6xx-07 

 

 

 33  

the software instructions. An alternative is to reset device to factory defaults using factory-
defaults button. 

I forgot the password for setup 

Please reset device to factory defaults. Procedure is described at following point. 

Factory defaults 

This procedure restore device to factory settings including network parameters (IP address, 
Subnet mask, etc.). Settings relating to measurement are not restored by factory defaults. For 
factory-defaults follow these steps: 

•

 

disconnect the power supply 

•

 

unscrew upper cover of the device case 

•

 

close the jumper inside device 

•

 

press button inside device and power on device at same time 

•

 

keep the button pressed for 10 sec 

 

 

 

•

 

close the device 

Display is off 

Check if power supply is connected. Disconnect power connector and connect connector 
again 

–

 watch the display at the moment of connecting the power. If all LCD segments light 

for 1 second and go out again, the display is turned off by software. 

Содержание T0610

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды