ComAp intelilite nt amf20 Скачать руководство пользователя

Страница: 62 / 145

InteliLite

– AMF20/25, SW version 2.2, ©ComAp – September 2014 62

IL-NT-AMF-2.2-Reference Guide.pdf

The output opens, if



alarm is not active and



FAULT RESET is pressed

AL Overcurrent

Output closes if the generator

*IDMT over current or
current unbalance or
short current alarm activates.

The output opens, if

Alarm is not active and

FAULT RESET is pressed

AL BatteryFail

Output closes when IL-NT performs reset during start procedure (probably due to weak battery) or
when battery under/over voltage warning appears.
The output opens, if



alarm is not active and



FAULT RESET is pressed

AL EarthFault

Output closes when Earth Fault Current is detected (extension module is needed).
The output opens, if



alarm is not active and



FAULT RESET is pressed

Hint:

For more details see chapter

Earth Fault Measurement

AL Common Wrn

Output closes when any warning alarm appears.
The output opens, if



No warning alarm is active and



FAULT RESET is pressed

AL Common Sd

Output closes when any shut-down alarm appears.
The output opens, if



No Sd alarm is active and



FAULT RESET is pressed

AL Common BOC

The output closes when any BOC alarm appears.
The output opens, if:



No BOC alarm is active and



FAULT RESET is pressed

AL Common Fls

Output closes when any Sensor Fail alarm appears.
The output opens, if



No warning alarm is active and



FAULT RESET is pressed

AL AI1 Sd

Output closes if the engine oil pressure (configured to the first analog input) shutdown alarm activates.
The output opens, if

Содержание intelilite nt amf20


















































































































































Результаты поиска

Содержание intelilite nt amf20

Отзывы:

Похожие инструкции для intelilite nt amf20

Бренды по названию

Популярные бренды

ComAp intelilite nt amf20, Справочное руководство

Результаты поиска

Содержание intelilite nt amf20

Отзывы:

Похожие инструкции для intelilite nt amf20

Бренды по названию

Популярные бренды