ComAp InteliDrive FLX LITE Скачать руководство пользователя

Страница: 121 / 228

ID-FLX Lite Global Guide

121

Setpoint group

Engine parameters

Related FW

2.5.0

Range [units]

0.0 .. 300.0 [s]

Default value

0.5

Step

0.1

Comm object

10525

Related applications

Description

This setpoint adjusts the Fuel solenoid output activation in relation to Starter output when Fuel solenoid =

GAS. Setpoint values mean that fuel valve is opened after the Starter. FuelSol offset has effect for both Fuel

solenoid = DIESEL or GAS.

Engine starting procedure when

Fuel solenoid (page 120)

= GAS

Note:

A new feature has been added which prolongs the last cranking attempt by 25% of MaxCrank time

with closed Fuel valve (Fuel Solenoid binary output) in order to ventilate the remaining gas, as is

implemented in IG/IS-NT. This function is valid only when

Fuel solenoid (page 120)

= GAS

Note:

Is modified functionality of the Ignition binary output. The Ignition binary output will close 1 second

(fixed value) after activation of binary output Fuel solenoid (when Fuel solenoid = GAS setting is active).

Generally, the output closes after reaching value of CrankRPM = 30RPM (fixed value). The output opens

after stopping of the engine or during crank fail pauses among crank attempts.

FuelSol offset

back to List of setpoints

Содержание InteliDrive FLX LITE





































































































































































































































Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды

ComAp InteliDrive FLX LITE, Руководство пользователя

Результаты поиска

Содержание InteliDrive FLX LITE

Отзывы:

Похожие инструкции для InteliDrive FLX LITE

Бренды по названию

Популярные бренды