ComAp InteliDrive DCU Industrial Скачать руководство пользователя

Страница: 25 / 350

InteliDrive DCU Industrial 3.4.0 Global Guide

1. Internet connection via AirGate – using InteliBridge-NT (IB-NT). No fixed and public IP address is needed.

2. Internet connection without AirGate – using InteliBridge-NT (IB-NT) or IG-IB module. The module has to

have fixed and public IP address.

Note:

The WebSupervisor ComAp tool is supported from ID-DCU Industrial version 3.1, specifically from ID-

DCU-INDUSTRIAL-W-3.1.mhx firmware.

2.3 List of supported modules

Product

Description

Order code

Inteli AIN8

8 Analog inputs (R,

I, V) and 1

pulse/frequency

input

I-AIN8

Inteli AIN8TC

8 Thermocouple

Analog inputs

I-AIN8TC

Inteli IO8/8

8 Binary inputs, 8

Binary outputs and

2 Analog outputs

packed in a small

unit (HW

switchable to

IO16/0). HW

switchableto IO16/0

- 16 Binary inputs

I-IO8/8

IS-BIN 16/8

16 configurable

galvanically

separated inputs, 8

configurable

IS-BIN16/8

Содержание InteliDrive DCU Industrial































































































































































































































































































































































Результаты поиска

Содержание InteliDrive DCU Industrial

Отзывы:

Похожие инструкции для InteliDrive DCU Industrial

Бренды по названию

Популярные бренды

ComAp InteliDrive DCU Industrial, Глобальное руководство

Результаты поиска

Содержание InteliDrive DCU Industrial

Отзывы:

Похожие инструкции для InteliDrive DCU Industrial

Бренды по названию

Популярные бренды