ComAp IM-NT Скачать руководство пользователя

Страница: 190 / 328

InteliMains

, SW version 3.0

InteliMains-NT-BTB-3.0-Reference Guide.pdf,

©ComAp – June 2013

190

possible

Description

This setpoint is used to adjust the relative load level (in % of total power
transferred from busL to busR -

NominBusLImp

) for load shedding. When the

power transferred through BTB exceeds this level for more than

Ld shed

delay

time the next load shedding output is closed.

OTE

Learn more about load shedding in the separate chapter

Load shedding

12.2.12.2

Setpoint: Ld shed delay

Group

Load shedding

Range [units]

0.0 .. 600.0 [s]

Related FW

3.0

Force value
possible

YES

Description

This setpoint is used to adjust time period the percentage of the power
transferred through BTB must be above the

Ld shed level

limit to close the

next load shedding output.

OTE

Learn more about load shedding in the separate chapter

Load shedding

12.2.12.3

Setpoint: Ld recon level

Group

Load shedding

Range [units]

0 ..

Ld shed level

[%]

Related FW

3.0

Force value
possible

YES

Description

This setpoint is used to adjust the relative load level (in % of total power
transferred from busL to busR -

NominBusLImp

) for load reconnection. When

the power transferred through BTB drops below this level for more than

recon delay

time the next load can be reconnected back.

The appropriate load shedding output is either opened automatically when
the condition above is fulfiled (

AutoLd recon

= ENABLED) or manually by

activation of the input

ManualLdRecon

OTE

Содержание IM-NT









































































































































































































































































































































Результаты поиска

Содержание IM-NT

Отзывы:

Похожие инструкции для IM-NT

Бренды по названию

Популярные бренды

ComAp IM-NT, Справочное руководство

Результаты поиска

Содержание IM-NT

Отзывы:

Похожие инструкции для IM-NT

Бренды по названию

Популярные бренды