COMAC ANTEA 50 B, Руководство по эксплуатации и обслуживанию

Страница: 23 / 44

WORK
STARTING WORK (B versions)
To start working, do as follows:
1. Make all the checks listed in “ PREPARING TO WORK ”.
2. Get in the driving seat, behind the machine.
3. Press the main system control button (1) so it is in the “work” position ( Fig. 1 ).
N.B.
: when the main system control button is functioning, the LED inside it is activated.
1
1
ON
SCRUBBING AND DRYING (B versions)
To carry out “SCRUBBING AND DRYING” tasks, proceed as follows:
1. Carry out all the checks indicated in the section “ STARTING WORK (B versions) ”.
2. Lower the brush head unit by pressing the brush head control pedal (1) on the back of the appliance
( Fig. 1 ).
3. Activate the brush head gearmotor using the brush control switch (2) ( Fig. 2 ).
4. Lower the squeegee unit by means of the lever (3) on the back of the appliance ( Fig. 3 ).
5. By activating the dead man's lever (4), the machine will start to move ( Fig. 4 ).
6. Activate the vacuum motor by pressing the relative switch (5) on the control panel (
Fig. 5
).
7. Activate the supply of detergent solution by pressing the switch (6) on the control panel ( Fig. 6 ).
8. Check the detergent solution tap is fully open. If it isn't, turn the lever (7) on the back of the appliance
( Fig. 7 ).
9. During the first few metres, check that the detergent solution is suitable for the work to be carried out.
If it isn't, make the necessary changes after reading the paragraph “ ADJUSTING THE DETERGENT
SOLUTION (versions without CDS system) ”.
The appliance will now begin to work with full efficiency until the battery is flat or until the detergent
solution has finished. During the first few metres, check that there is sufficient solution and that the
squeegee is drying correctly.
N.B. : if during the scrubbing - drying operation the dead man's lever is released, the brush motor
and the solenoid valve will stop working, the vacuum motor will continue to work for a few seconds
to ensure all the liquid in the vacuum hose is sucked up.
N.B. : when filling the solution tank, it is good practice to empty the recovery tank using the special
drainage hose.
N.B. : by pulling the detergent solution flow adjustment knob downwards, the amount of solution in
the water system will increase (
Fig. 7
).
1
2
4
1 2 3
4
5 6
4 5 6
7
7
SCRUBBING WITHOUT DRYING (B versions)
To carry out “SCRUBBING WITHOUT DRYING” tasks, proceed as follows:
1. Carry out all the checks indicated in the section “ STARTING WORK (B versions) ”.
2. Lower the brush head unit by pressing the brush head control pedal (1) on the back of the appliance
( Fig. 1 ).
3. Activate the brush head gearmotor using the brush control switch (2) ( Fig. 2 ).
4. By activating the dead man's lever (3), the machine will start to move (
Fig. 3
).
5. Activate the supply of detergent solution by pressing the switch (4) on the control panel ( Fig. 4 ).
6. Check the detergent solution tap is fully open. If it isn't, turn the lever (5) on the back of the appliance
( Fig. 5 ).
7. During the first few metres, check that the detergent solution is suitable for the work to be carried out.
If it isn't, make the necessary changes after reading the paragraph “ ADJUSTING THE DETERGENT
SOLUTION (versions with CDS system) ”.
The appliance will now begin to work with full efficiency until the battery is flat or until the detergent
solution has finished. During the first few metres, check that there is sufficient solution.
N.B. : if the dead man's lever is released during the scrubbing and drying operation, the brush
motor and solenoid valve will stop working. To resume work, just press the dead man's levers.
N.B. : by pulling the detergent solution flow adjustment knob downwards, the amount of solution in
the water system will increase ( Fig. 5 ).
1
3
2
1 3 2
4
4
5
5
DRYING (B versions)
To carry out “DRYING” tasks, proceed as follows:
1. Carry out all the checks indicated in the section “ STARTING WORK (B versions) ”.
2. Lower the squeegee unit by means of the lever (1) on the back of the appliance ( Fig. 1 ).
3. By activating the dead man's lever (2), the machine will start to move ( Fig. 2 ).
4. Activate the vacuum motor by pressing the relevant switch (3) on the control panel ( Fig. 3 ).
The machine will now work at its maximum efficiency level until the batteries run down.
N.B. : if the dead man's lever is released during the drying operation, the vacuum motor will
continue working for another few seconds so that all the liquid in the vacuum hose can be
removed.
2
3
1
2 3 1
The drying without scrubbing operation should only be carried out if
beforehand the device was used to carry out scrubbing without drying.
23