background image

11

S

ectioN

 5 — o

peratioN

Operating the Tiller

Select the depth stake setting.

1. 

Start the engine as instructed on the previous page.

2. 

Move the gear selection handle to one of the forward 

3. 

modes or reverse.

WARNING! 

Do not move the gear selection handle 

with the wheels or tines engaged. Make certain the 

tiller is stopped completely before changing the 

gear selection. A partial engagement may be 

necessary when engaging tines.

To shift into forward wheels and tine drive, push forward 

4. 

slightly on the gear selection handle and slowly engage 

the clutch control allowing the gears to synchronize. To 

stop forward movement and tine drive, release the clutch 

control. Do not shift gears with the clutch control engaged 

except when engaging the tines.

NOTE: 

Use the reverse tine drive when tilling virgin 

ground, sod, or hard soil. Use the forward tine drive when 

cultivating or tilling soft ground.
Squeeze the clutch handle against the handle to engage 

5. 

the wheels and tines.

NOTE: 

Make certain the gear selection indicator is correctly 

positioned before engaging the clutch handle. If it is 

between the gears, the engine will stall.
To transport the tiller, do not engage the tines. Select the 

6. 

wheel drive only.

WARNING! 

Do not push down on the handles so 

that the wheels are lifted off the ground while using 

the tine drive, or the tiller could move backward and 

cause personal injury.

For best results, it is recommended the garden be tilled 

7. 

twice (lengthwise, then width-wise) to pulverize the soil.

Содержание 450 Series



















Отзывы: