background image

7.

7.

7.

7. Photometric

Photometric

Photometric

Photometric Data

Data

Data

Data

8.DMX

8.DMX

8.DMX

8.DMX Channels

Channels

Channels

Channels

Chanel

Chanel

Chanel

Chanel

Function

Function

Function

Function

Values

Values

Values

Values

Description

Description

Description

Description

1

Pan

0-255

PAN Movement

2

Pan Fine

0-255

Fine control of Pan movement

3

Tilt

0-255

Tilt Movement

4

Tilt Fine

0-255

Fine control of Tilt movement

5

Color

0-019

Open/White

020-039

Color 1

040-059

Color 2

060-079

Color 3

080-099

Color 4

100-127

Color 5

128-189

Color 6

190-193

Color 7

194-255

Forwards rainbow effect from fast to slow

from a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at

least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent accidental damage

and/or injury in the event the clamp fails.

Mounting

Mounting

Mounting

Mounting points

points

points

points::::

Overhead mounting requires extensive experience, including amongst others

calculating working load limits, a fine knowledge of the installation material being used, and

periodic safety inspection of all installation material and the fixture. If you lack these qualifications,

do not attempt the installation yourself. Improper installation can result in bodily injury.

Be sure to complete all rigging and installation procedures before connecting the main power

cord to the appropriate wall outlet.

Clamp

Clamp

Clamp

Clamp Mounting

Mounting

Mounting

Mounting::::

The LED Beam Moving Head provides a unique mounting bracket assembly

that integrates the bottom of the base, the included “Omega Bracket,” and the safety cable rigging

point in one unit (see the illustration below). When mounting this fixture to truss be sure to secure

an appropriately rated clamp to the included omega bracket using a M10 screw fitted through the

center hole of the “omega bracket”. As an added safety measure be sure to attached at least one

properly rated safety cable to the fixture using on of the safety cable rigging point integrated in

the base assembly

Содержание SI-053







Отзывы: