Colop digital e-mark create Скачать руководство пользователя страница 11

Страница: 11 / 60

e-mark create marking device

Chapter 2 Safety

CODI Standard 1.0

11/60

Operating and Maintenance Manual

2.3 Residual hazards

Even when the greatest care and attention is paid to the design and build of the product, and when full account is

taken of safety-related factual content, residual hazards can still exist, which were evaluated in a risk assessment.

DANGER!

Hazard from electric shock. There is a risk of a fatal electric shock in wet

conditions.

Never handle the charger mains plug with wet hands. Never use the device in humid
areas. Never expose the battery and charger, including USB port, to water and/or rain.

WARNING!

Danger of suffocation from plastic film.

The packaging is not a toy. Dispose of packaging materials immediately and in an

environmentally appropriate manner.

WARNING!

Risk of asphyxiation from small parts for children below the age of three.

The device is not a toy. Do not leave children alone with the device unsupervised.

WARNING!

Hazard from cleaning.

NEVER use inflammable substances near the e-mark create. This may cause a fire or

an electric shock.

Cleaning the outside of the e-mark create:

- Ensure that the mains cable of the e-mark create charger has been removed from the

socket and the device is switched off.

- Use neutral cleaning agent. Using liquids such as thinners or petrol damages the

outer surface of the e-mark create.

- Do NOT use cleaning agents containing ammonia.

Содержание digital e-mark create





























































Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды

Colop digital e-mark create, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание digital e-mark create

Отзывы:

Похожие инструкции для digital e-mark create

Бренды по названию

Популярные бренды