background image

-- 16 -- 

 

w torque limit mode is being used. To protect the mixer head 

rrected.   

N

 Cole-Par

r for repair, try to determ

ad

way is to substitute a known go

vailable, and 

 ACCE

T

sed

ounting the mixer head and controller, are available from Cole-

P

 other ccessories such as shafts and impellers 

ailable.  

Contact your dealer for the full line of available accessories.   

Part Number 

“HI” Limit Message 

A flashing “HI” limit message will be displayed and the mixer head will stop if the maximum rated torque
of the mixer head is exceeded when the lo
motor from o

g, it cannot be re

verheatin

started until the fault is co

r deale

ote:  

Before contacting

ller or mixer he

mer or you

ine whether the fault is in 

the contro

. The best 

od unit, if a

recheck. 

SSORIES 

he accessories listed below, u

 for m

armer or your dealer.  Many

 a

are also av

Part Name  

Tank Clamp  

04552-65 

Controller Support Platform 

04552-75 

Pivot Mount Controller Support  

04552-70 

Support Stand  

04552-80 

Double (Rod) Clamp  

08041-22 

Software  

07550-74 

ServoDyne RS-2

07550-64 

32-C Interface Cable 

Satellite Cable  

07550-66 

Shaft, 12 inches (305 mm) 

04552-25 

Shaft, 18 inches (457 mm) 

04552-35 

Shaft, 24 inches (610 mm) 

04552-00 

Shaft, 30 inches (762 mm) 

04552-05 

 

 W

turer warrants this product to be free fro

r adjustment is necessary

h

  

if it is not due to misuse or abuse on your part as deter

ufacturer. Repair costs 

outside the warranty period, or those resulting from

, may be invoiced to 

you. 

The warranty period for this product is noted on th

g from improper 

ing are your responsibility.   

TECHNICAL ASSISTANCE 

I

a

out the use 

dealer.   

 

 

 

SSMPK027  Rev 2.01 

ARRANTY 

The manufac

m

ed 

 wit in the warranty period, the problem will be 

mined by the man

 significant deviations from publish

specifications.  If repair o
corrected at no charge

 product misuse or abuse

e Warranty Card.   

PRODUCT RETURN 

To limit charges and delays, contact Cole-Parmer or manufacturer for authorization and shipping 
instructions before returning the product, either within or outside of the warranty period.  When 
returning the product, please state the reason for the return.  For your protection, pack the product 
carefully and insure it against possible damage or loss.  Any damages resultin
packag

f you h ve any questions ab

of this product, contact Cole-Parmer or your local 

 

 

Содержание ServoDyne 50008-00

















Отзывы: