Cole Parmer Masterflex 07525-20 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 66

background image

3-18

MASTERFLEX

®

Digital Pump Drive Operating Manual

Cole-Parmer

Section 3

Operation

This allows the user to input a current signal to control the RPM. The
user has an option to adjust the minimum, maximum and middle set
points for current and RPM. By default the minimum (MIN) current is
set to 4.1 mA and the RPM is set to 0.0. The maximum (MAX) is set to
20.0 mA and the RPM is set to maximum. The scaling can be inverted, if
necessary. The RPM is linear between these two points. After both
setpoints have been adjusted, save both setpoints from the upper setpoint
setting screen by highlighting the save icon and pressing ENTER.

To confirm CURRENT INPUT MODE is ON, press the BACK key
until the CONTINUOUS PUMP MODE screen appears. The Current
input icon will be displayed.

NOTE:

When Current Input is selected the drive will not start until the

CURRENT INPUT is ON and in CONTINUOUS PUMP MODE.

Remote Control

Current Input Menu

(continued)

«
...
30
31
32
33
34
...
»

Содержание Masterflex 07525-20



































































Отзывы:

Нет отзывов

Похожие инструкции для Masterflex 07525-20

Бренд: Q-Pumps Страницы: 44

the Vac Q SBL002

Бренд: Sage Страницы: 80

Бренд: Xylem Страницы: 44

Бренд: Barnes Страницы: 16

Бренд: T.I.P. Страницы: 104

HYDROMATIC SP50

Бренд: Pentair Pool Products Страницы: 12

Бренд: Waterous Страницы: 7

Бренд: CleanCraft Страницы: 22

Бренд: Graco Страницы: 10

Бренд: GPI Страницы: 26

Бренд: OmarLift Страницы: 32

Бренд: K2 Pumps Страницы: 29

Бренд: Waterax Страницы: 32

Бренд: ebm-papst Страницы: 9

Бренд: Tyco Страницы: 2

Бренд: Daikin Страницы: 40

Бренд: Daikin Страницы: 36

Daikin Altherma 3 H F+W

Бренд: Daikin Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды