Cognex COV-7000-CMNT Скачать руководство пользователя страница 9

Страница: 9 / 84

Introduction

The In-Sight

vision system is a compact, network-ready, stand-alone machine vision system used for automated

inspection, measurement, identification and robot guidance applications on the factory floor. All models can be easily

configured remotely over a network using an intuitive user interface.

Support

Many information resources are available to help you use the vision system:

The

In-Sight

ViDi Help

file.

The

In-Sight

Vision Suite Help

file.

Standard Components

Note

Cables are sold separately.

If a standard component is missing or damaged, immediately contact your Cognex Authorized Service

Provider (ASP) or Cognex Technical Support.

Component

Description

Vision System

Provides image acquisition, vision processing, job storage, Ethernet connectivity and discrete I/O.
The vision system has an 8GB SD card pre-installed.

Introduction

Содержание COV-7000-CMNT





















































































Результаты поиска

Содержание COV-7000-CMNT

Отзывы:

Похожие инструкции для COV-7000-CMNT

Бренды по названию

Популярные бренды

Cognex COV-7000-CMNT, Справочное руководство

Результаты поиска

Содержание COV-7000-CMNT

Отзывы:

Похожие инструкции для COV-7000-CMNT

Бренды по названию

Популярные бренды