Cognex COV-7000-CMNT Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 84

background image

High-Speed Outputs

The vision system features four

1

built-in, high-speed outputs, which are optically isolated. The high-speed outputs can be

used as either NPN (current sinking) or PNP (current sourcing) lines.

Specification

Description

Voltage

26.4VDC maximum through external load

Current

50mA maximum sink or source current

OFF state leakage current 100µA

External load resistance 470 Ohms to 10K Ohms

Each line rated at a maximum 50mA, protected against over-current, short circuits and transients from
switching inductive loads. High current inductive loads require an external protection diode.

Delay
(Electrical)

15ms ON time (maximum) and 40ms OFF time (maximum)

For NPN lines, the external load should be connected between the output and the positive supply voltage (<26.4VDC).

The output pulls down to less than 3VDC when ON, which causes current to flow through the load. When the output is

OFF, no current flows through the load.

For PNP lines, the external load should be connected between the output and the negative supply voltage (0VDC).

When connected to a 24VDC power supply, the output pulls up greater than 21VDC when ON, and current flows through

the load. When the output is OFF, no current flows through the load.

1

When connected to the Breakout cable, the vision system allows for bi-directional, general-purpose inputs and high-speed outputs for IN 2 /
HSOUT 2 and IN 3 / HSOUT 3. These lines are configured as outputs by default.

66

Specifications

«
...
64
65
66
67
68
...
»

Содержание COV-7000-CMNT





















































































Отзывы:

Нет отзывов

Похожие инструкции для COV-7000-CMNT

Бренд: Janome Страницы: 2

Бренд: Janome Страницы: 5

Бренд: Adler Страницы: 5

Бренд: Baby Lock Страницы: 2

Бренд: Singer Страницы: 56

Бренд: JUKI Страницы: 34

Бренд: ADLINK Technology Страницы: 84

Бренд: SRT Страницы: 73

Бренд: Yamato Страницы: 30

Бренд: Singer Страницы: 17

Бренд: Singer Страницы: 18

Бренд: Husqvarna Viking Страницы: 60

Бренд: VERITAS Страницы: 80

Бренд: VERITAS Страницы: 104

SPS/A-Pattern Series

Бренд: SunStar Страницы: 195

Tecnovita My Step YF63

Бренд: BH Страницы: 20

Enterprice BNT10L

Бренд: Baby Lock Страницы: 13

Бренд: Janome Страницы: 55

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды