Cognex CC24 Скачать руководство пользователя страница 10

Страница: 10 / 35

Install the Communication Card to the PC

CAUTION

Electrostatic discharge (ESD) can damage the electronic components of the Cognex hardware; wear a

grounded, static-dissipating wrist strap for ESD protection.

1. Power off the PC and remove its cover.

2. Select a PCI Express x1 slot. Remove the slot cover and store it for future use.

3. Press the board into the slot until it is firmly seated.

4. Replace the PC's cover.

CAUTION

Do not power on the PC until you have connected any I/O devices to the Communication card.

Connect I/O Devices (Optional)

The Communication card supports the connection of PLCs and photoelectric sensors, as well as general use I/O

devices, such as relays, indicator lights and reject mechanisms. The Communication card also supports connection to

either a single-ended or differential encoder. For more information, refer to

and

There are two options for connecting I/O devices: using the accessory Breakout cable; or the I/O Terminal Block cable

and DIN-rail mountable Terminal Block accessories.

If connecting the Breakout cable to the Communication card, the cable's flying lead wires can be connected

directly to the applicable I/O device.

If connecting the I/O Terminal Block cable to the Communication card, the cable is connected to the Terminal

Block, which can be connected directly to the applicable I/O device.

Connect the Breakout Cable

1. Determine how I/O devices will be connected to the Communication card's inputs and outputs. Refer to

Wire

Inputs and Outputs

on page 27

for common wiring configurations.

2. Make sure all I/O devices and the PC hosting the Communication card are powered off.

3. Connect the Breakout cable's MDR connector to the MDR connector on the Communication card.

4. Connect the Breakout cable's flying lead wires to the applicable I/O device. Refer to

Breakout Cable

Specifications

on page 20

for cable pin-outs.

Installation

Содержание CC24




































Результаты поиска

Содержание CC24

Отзывы:

Бренды по названию

Популярные бренды

Cognex CC24, Руководство по оборудованию

Результаты поиска

Содержание CC24

Отзывы:

Бренды по названию

Популярные бренды