Cognex CC24 Скачать руководство пользователя страница 14

Страница: 14 / 35

Inputs

The Communication card features eight independent inputs (INPUTS 0 - 7), which can be used to trigger events. The

inputs are optically isolated and typically connected (directly or indirectly) to a PLC or photoelectric sensor. The

Communication card will respond to an event when the voltage difference between the INPUT and INPUT COMMON

exceeds 10VDC. Refer to

Wire Inputs and Outputs

on page 27

for common wiring configurations.

Note

There are two sets of inputs: INPUTS 0 - 3 share the INPUT COMMON 1 connection and INPUTS 4 - 7 share

the INPUT COMMON 2 connection. Therefore the input devices for each set of inputs must be the same;

either current sinking or current sourcing.

To maintain optical isolation of the I/O lines, the devices connected to these lines must not be connected to

the same power supply as the PC. If they are connected to, or share a ground with, the same power supply,

they may still function but will no longer be optically isolated.

Specification

Description

Input Voltage Limit

24VDC

Voltage

Input ON: >10VDC
Input OFF: < 2VDC

Current

Input ON: > 6mA
Input OFF: < 1.5mA
Each line is optically isolated and polarity-independent.

Specifications

Содержание CC24




































Результаты поиска

Содержание CC24

Отзывы:

Бренды по названию

Популярные бренды

Cognex CC24, Руководство по оборудованию

Результаты поиска

Содержание CC24

Отзывы:

Бренды по названию

Популярные бренды