COFFEtek VITRO S3 Скачать руководство пользователя страница 28

Страница: 28 / 68

COFFE

tek

LTD

VITRO S3

Revision 1

28/02/2017



FILE TYPE



DESTINATION



Configuration files



"./Coffetek/Zmcu/Configs/"



Timed Events



"./Coffetek/Zmcu/TimEvts/"



Prices



"./Coffetek/Zmcu/Prices/"



Audits



"./Coffetek/Zmcu/Audits/"

ACHINE

ERIAL

UMBER

32.



Press ENTER, if not set press ENTER again. The display will show:

MACHINE SERIAL #
VALUE 00000 (FLASHING DIGIT)



To set serial number press



(UP) to increase or



(DOWN) to decrease, or press



(lLEFT)



(RIGHT) to move cursor.

TATUS

33.

The I²C status menu contains the following submenus;



Plus 16 Status



Coin Pod Status

For each of the above sub menus the following options are available;

Menu Item

Description

I2C ACKS

The number of successful messages transferred since power on. Can wrap
around to 0.

I2C NAKS

The number of unsuccessful messages transferred since power on. Can wrap
around to 0.

ISOLATION
TEST

Shuts down all I²C communication with other devices. Continues communication
with the device under test and feeds back real time ACKS or NAKS.



ATE

34.

The SET DATE AND TIME menu configures the Real time clock facility now available on
the control board.

Содержание VITRO S3





































































Результаты поиска

Содержание VITRO S3

Отзывы:

Похожие инструкции для VITRO S3

Бренды по названию

Популярные бренды

COFFEtek VITRO S3, Техническое руководство

Результаты поиска

Содержание VITRO S3

Отзывы:

Похожие инструкции для VITRO S3

Бренды по названию

Популярные бренды