4.4. Error messages
ESYS
Operating system error, often caused by an incomplete data transfer from DR-2. Retry the data transfer to correct the problem.
EFIX
Memory error, often caused by an incomplete data transfer from DR-2. Retry the data transfer to correct the problem.
EDMX
Communication error between the fixture processor and DMX. If caused by a recent incomplete data transfer from DR2 retry
the transfer, upgrade the DMX software or replace the CE107 Main PCB.
DMX ERR
DMX communication error. Verify that DMX data is present. Possible causes include the wiring between the DMX input and
CE107 Main PCB or defective CE107 PCB.
(MOTOR NUMBER) NO LINK
Communication error between the CE107 Main PCB and the indicated motor. Possible causes include the wiring between
CE107 PCB and the Motor PCB or the Motor PCB may have failed.
FAN2 NO LINK
Communication error between the CE107 Main PCB and the fan driver board on bus 2. Possible causes include the wiring
between CE107 PCB and the Fan PCB or the Fan PCB may be defective.
FAN4 NO LINK
Communication error between the CE107 Main PCB and the fan driver board on bus 4. Possible causes include the wiring
between CE107 PCB and the Fan PCB or the Fan PCB may be defective.
BUS2 FAIL
The number of motor cards found on bus 2 does not match the software version installed.
BUS4 FAIL
The number of motor cards found on bus 4 does not match the software version installed.
(MOTOR NUMBER) RST ERR
The indicated motor has failed to reset in the allotted time. Check that the motor is free to move and that the wiring from the
motor board to the motor is intact. Use the sensor test mode to verify that the sensor is detecting the motor when the sensor
passes the magnet or the flag interrupts the opto sensor.
(MOTOR NUMBER) INI ERR
The indicated motor has not completed its initialization routine in the allotted time.
Check that the motor is free to move and that the wiring from the motor board to the motor is intact. Use the sensor test mode
to verify that the sensor is detecting the motor when the sensor passes the magnet or the flag interrupts the opto sensor.
(MOTOR NUMBER) OPTO ERR
The opto sensor associated with this motor did not detect the flag. Check that the motor is free to move and that the wiring
from the motor board to the motor is intact. Use the sensor test mode to verify that the sensor is detecting the motor when the
flag passes through the opto sensor. Check that the sensor is clean.
(MOTOR NUMBER) ENC ERR
The position encoder associated with the motor has detected an error. This may be due to the opto sensor or encoder wheel
failing to properly encode the motor motion. Check the sensor, encoder and wiring.
(FAN NUMBER) ERR
The indicated fan has produced an error. Fan velocity is returned to the microprocessor through a third wire on the fan motor.
Check that the fan is free to move, that the wiring from the fan to the fan board is intact. Check that the air filters are clean and
airflow is unrestricted.
DR2L
Flex is connected to
dr2
, The
+
/
-
/
menu
/
enter
/
more
buttons are disabled
UPGR
indicates upgrade in process.
Flex is connected to
dr2
, The
+/-/menu/enter/more
buttons are disabled, software upgrade is active.
4.5. Special Features
Turning on the iSPOT FLEX without movement
This function may be useful should you need to power up the fixture inside its roadcase or for any other reason where you
may wish to power up the unit without it moving pan and tilt motors. All motors will be energized and reset as normal except for
pan and tilt motors.
1) Power up the projector while pressing the
<more>
button.
The projector will switch on without the usual reset functions.
You may at this point alter a DMX address, or any other menu-based parameter without pan and tilt movement.
This function is particullarlty useful to test the sensors, load the new software to PCBs and to re-address the PCBs network.
4) To resume normal fixture functioning, you must turn the projector off and on again via the
power
button or reset the light using
the display
RST
command
11
Содержание iProfile Flex
Страница 1: ...2st edition july 2004 provisional instruction manual...
Страница 2: ......
