Coemar CF 1200 Hard Edge Скачать руководство пользователя

Страница: 16 / 42

11. Display panel

The display panel at the rear of the

CF 1200 H

ard

dge

is used to display and set

functions

function information and various parameters.
Altering the

coemar

factory settings may vary the functioning of the projector, cau-

sing it to not respond to external

DMX 512

signal. Please read and familiarise your-

self with the following information very carefully before altering any selections.

reset

This function causes a reset to occur in the case (however unlikely) that one or more
of the motors should lose its reference point.
1) Press the

menu

button.

2) Press the

button until the display shows

rESE

(for reset).

3) Press the

enter

button to confirm your selection; all the motors will perform a

reset.

rate

This function provides information on the speed or rate of DMX 512 signal being
received by the

CF 1200 H

ard

dge

1) Press the

menu

button.

2) Press the

button until the display shows

rAtE

(for rate/speed).

3) Press the

enter

button to confirm your selection; il display visualizza un valore

numerico che è la velocità di trasmissione del segnale

DMX 512

hour

Permette di visualizzare la vita del proiettore, ovvero il numero di ore nelle quali

1200 H

ard

dge

è stato alimentato.

1) Press the

menu

button.

2) Press the

button until the display shows

HoUr

(per ore).

3) Press the

enter

button to confirm your selection; the display will show a numeri-

cal value which is the rate/speed of the DMX 512 signal being received.

life

This function provides information on the number of hours of operation of the lamp
in the unit.
1) Press the

menu

button.

2) Press the

button until the display shows

LIFE

(for lamp life).

3) Press the

enter

button to confirm your selection; the display will show a numeri-

cal value which is the length of time in hours that the lamp has been operated
since the counter was last reset.

function display

Содержание CF 1200 Hard Edge











































Результаты поиска

Содержание CF 1200 Hard Edge

Отзывы:

Похожие инструкции для CF 1200 Hard Edge

Бренды по названию

Популярные бренды

Coemar CF 1200 Hard Edge, Инструкция по эксплуатации

Результаты поиска

Содержание CF 1200 Hard Edge

Отзывы:

Похожие инструкции для CF 1200 Hard Edge

Бренды по названию

Популярные бренды