Code Soft PL-330D Скачать руководство пользователя страница 12

Страница: 12 / 101

CODESOFT PL-330 User's Manual

- 6 -

2.4 Connecting the Power

1. Make sure the printer is turned off. (The pressed down side on the switch with “O” mark denotes the

printer is off)

2. Make sure the voltage of the electrical outlet matches that of the AC adapter.

3. Plug the AC adapter to the printer’s power supply inlet.

4. Plug one end of power cord into the AC adapter, and then plug the other end of the power cord into

the grounded electrical outlet.

Figure 2-7 Connecting the power

Figure 2-6 Connecting the Ethernet cable

Note: Please refer to the

user’s manual

for detailed instructions of network settings.

Warning: 1. If the rated voltage doesn’t match the outlet voltage, contact your dealer

for assistance. Do not plug the power cord to electrical outlet.

2. Please use the electrical outlet connecting the ground properly.

3. Please use the original AC adapter only. Manufacturers have no

responsibilities for the problems which are led by using unauthorized AC
adapter.

Ethernet interface

Ethernet cable

Power cord

AC adapter

Power supply inlet

Содержание PL-330D






































































































Результаты поиска

Содержание PL-330D

Отзывы:

Похожие инструкции для PL-330D

Бренды по названию

Популярные бренды

Code Soft PL-330D, Руководство пользователя

Результаты поиска

Содержание PL-330D

Отзывы:

Похожие инструкции для PL-330D

Бренды по названию

Популярные бренды