Code Alarm PROFESSIONAL SERIES Скачать руководство пользователя страница 19

Страница: 19 / 24

10 - Arm/Disarm Chirps:

Determines the number of chirps and parking light flashes

when the system is armed/disarmed.

Standard - 2 chirps/light flashes with arm, 1 chirp/light flash with disarm.

Inverted - 1 chirp/light flash with arm, 2 chirps/light flashes with disarm.

11 - LED Indicator:

Control of the LED when the system is armed / locked.

ON - LED will flash when system is armed / locked

OFF – LED will not flash when system is armed / locked. Only applies to

normal operation (armed/locked) and does not affect programming, valet

mode, diagnostics, passive lock countdown or PTN

12 - Auto Re-Lock:

When Auto Re-lock is selected, the system will re-lock the

vehicle after 3 minutes if the system was disarmed and a door was NOT opened

within that set amount of time. A door opening within this time cancels Auto Re-Lock.

Note: This feature is separate from Passive/Active Arming

OFF – Standard operation.

Lock Only – The unit will re-lock the vehicle after 3 minutes if the system was

disarmed and a door was NOT opened within that time.

Arm & Lock (security units only) - The system will arm and also re-lock the

vehicle after 3 minutes if the system was disarmed and a door was NOT

opened within that time.

13 - Extended Parking Lights:

When selected, this feature will keep the parking

lights on for an additional 30 seconds after the standard flashes when pressing lock

or unlock.

OFF – Normal parking light function.

After Unlock – Parking lights will stay on for 30 seconds after normal unlock

flashes.

After Lock - Parking lights will stay on for 30 seconds after normal lock flashes.

After Lock & Unlock - Parking lights will stay on for 30 seconds after normal

lock and unlock flashes.

14 - Parking Light Relay / Trunk ( - ) Output:

This feature gives the installer the

ability to swap the functions of the Parking Light Relay & Trunk Output.

Standard – No change to outputs.

Inverted – When inverted, the Trunk Red / White ( - ) Output will function as the

Parking Light Output and the Parking Light White & White/ Red will function as

the Trunk Output.

15 - Not available on this model.

Содержание PROFESSIONAL SERIES

























Результаты поиска

Содержание PROFESSIONAL SERIES

Отзывы:

Бренды по названию

Популярные бренды

Code Alarm PROFESSIONAL SERIES, Руководство по установке

Результаты поиска

Содержание PROFESSIONAL SERIES

Отзывы:

Бренды по названию

Популярные бренды