manualshive.com logo in svg

Code Alarm PROFESSIONAL SERIES, Руководство по установке

Поделиться
Скачать
Code Alarm PROFESSIONAL SERIES Скачать руководство пользователя страница 18

18

ca1155 rev B

 

4 - System Notifications: 

This feature selects which output(s) will sound the 

system’s arm/disarm chirps. This feature does not effect the triggered state of the 

security system and during a triggered cycle, both the siren and horn outputs will 

activate respectively.

   

Siren & Horn – Siren and horn both sound when arming/disarming the system.

   

Siren Only – Only the siren will sound when arming/disarming the system.

   

Horn Only - Only the horn will sound when arming/disarming the system.

 

5 - Alarm Duration: 

Determines the length of time the system will sound the siren/

horn during a full trigger event. 

   

30 Seconds – When triggered, the system will sound the siren/horn for 30  

 

seconds then stop. The unit will remain armed and may be triggered again.

   

60 Seconds – When triggered, the system will sound the siren/horn for 60  

 

seconds then stop. The unit will remain armed and may be triggered again.

 

6 - Security: 

Controls security functionality - ON / OFF.

   

ON - Full security functionality.

   

OFF - The security system does not trigger. Panic and all other convenience  

 

features operate as normal.

   

ON w/OEM Remote Start Compatibility - This will prevent a vehicle’s factory  

 

remote start from triggering the security system when activated. The system  

 

will use the ignition input to shunt shock and door inputs until 5 seconds after  

 

they clear. If the alarm is triggered prior to ignition on, then ignition will not  

 

shunt/cancel the alarm’s triggered state. Also, note that the ignition input will no  

 

longer serve as a trigger if this option is selected on.

 

7 - Anti-Hijack Mode: 

Controls Car Jack mode - ON / OFF.

   

OFF - Standard security system operation.

   

ON - Enables Car Jack mode functionality as described in the owners    

 manual

 

8 - Ground While Armed / Orange Output:

 Controls the output of the orange wire. 

This wire will either supply a ( - ) output when armed OR disarmed.

 

9 - DBI Port Protocol:

 Determines the protocol type in which the DBI port uses to 

interface with external modules.

   

DBI Protocol

   

ADS Protocol

Содержание PROFESSIONAL SERIES

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды