manualshive.com logo in svg

Code Alarm Professional Series CA 1050, Руководство пользователя, Страница: 16 / 20

Поделиться
Скачать
Code Alarm Professional Series CA 1050 Скачать руководство пользователя страница 16

16

2009 Audiovox Electronics Corporation. All rights reserved.

2 - Passive Locks: Determines manual or automatic locking of the vehicle’s
doors.

Active - Requires use of the transmitter to lock the vehicle’s doors.

Passive - Automatically locks the vehicle’s doors 1 minute after the last door
is closed

3 - Passive Arming: Determines manual or automatic locking of the vehicle’s
doors.

Active - Requires use of the transmitter to arm the security system.

Passive - Automatically arms the security system 1 minute after the last door
is closed

4 - Hi Jack: Controls hi jack mode - ON / OFF.

OFF - Standard security system operation.

ON - Enables Hi Jack mode functionality as described in the owners manual

Feature Bank 3 - Output Control

1 - Extended Lock Pulse: Controls the timing of the BLUE and GREEN lock output
wires.

1 Second - Single 1 second lock pulse, single 1 second unlock pulse.

3.5 Seconds - Single 3.5 second lock pulse, single 3.5 second unlock pulse.

1 Second Lock, Double Pulse Unlock - Single 1 second lock pulse, double 1
second unlock pulse.

30 Second Lock, Double Pulse Unlock - Single 30 second lock pulse, double
1 second unlock pulse.

Double Pulse Lock, 1 Second Unlock - Double 1 second lock pulse, single 1
second unlock pulse.

2 - Ignition Controlled Locks: Control of door locks when the ignition is cycled
ON or OFF.

OFF - Door locks not activated by ignition.

Lock and Unlock - Doors lock when ignition is turned on and unlock when
ignition is turned off.

Lock Only - Doors lock when ignition is turned on.

Unlock Only - Doors unlock when ignition is turned off.

Содержание Professional Series CA 1050





















Отзывы:

Нет отзывов