Code 3 Thin WingMan MATRIX Series Скачать руководство пользователя страница 2

Страница: 2 / 16

Page 2 of 8

Unpacking and Pre-Installation:

Carefully remove the product and place it on a flat surface. Examine the unit for transit damage and locate all parts. If damage is found or

parts are missing, contact the transit company or Code 3. Do not use damaged or broken parts.

Ensure the product voltage is compatible with the planned installation.

Thin WingMan vehicle specific mounting kits are available on our website. For information on how to mount the Thin WingMan using vehicle

specific kits, please refer to the installation instructions provided with those kits.

A universal mounting bracket (P/N: TWMTG-UNIV) is also available. See below for installation instructions.

The Universal kit includes (2) 90 Degree Universal Mounting Brackets. These brackets can be bolted to the Outer Panel of the Thin WingMan

and modified as needed to mount the unit. The Thin WingMan must be hard mounted to the sheet metal of the vehicle to prevent injury to

passengers in the event of a collision. It is the installers responsibility to ensure the product is mounted securely. Make sure proper support

is provided between the vehicle’s sheet metal and the fiber/fabric of the package tray area as in many cases there is a substantial air gap

between them. In some cases you will need to self fabricate brackets to adapt the Thin WingMan to your vehicle.

Caution!!! When installing the unit do not push it too hard against the rear window. The unit only needs to just touch the glass

enough to fold the gasket flange back & block out as much flash back light as possible. A broken rear window can result if the unit

is installed too tight against the glass!

Installation and Mounting:

Содержание Thin WingMan MATRIX Series
















