manualshive.com logo in svg

Coda 07X, Руководство по эксплуатации, Страница: 4 / 14

Поделиться
Скачать
Coda 07X Скачать руководство пользователя страница 4

Illustrated below is the rear panel of the 07X. The connections are standard and typical of any

audio preamplifier. Any unknown features should be adequately explained by the function

descriptions on the following page.

Both sets of balanced receptacles on the left side are identical stereo outputs suitable for

connection to multiple amplifiers. The two sets of balanced receptables on the right side

are separate input channels.

Make sure during installation that the AC power connections are interrupted to the 

preamplifier and all other components are off. While the diagram may be self 

explanatory, we strongly recommend that you read the front panel description 

on the following page for use instructions. 

  

 3

 

INSTALLATION CONNECTIONS

BALANCED 2

        PROCESSOR  OUT

BALANCED 1

LEFT                                     

                     RIGHT

LEFT                      RIGHT

LEFT                      RIGHT

LEFT                      RIGHT

LEFT                      RIGHT

LEFT                      

RIGHT

RIGHT

LEFT

BALANCED 2

RIGHT

LEFT

BALANCED 1

LEFT                                     

RIGHT

        DISC

        AUX

        PROCESSOR  IN

        UNBALANCED  OUT

Содержание 07X















Отзывы:

Нет отзывов