.5.
.6.
Step
Clear
Mute
Title
Power
Menu
Enter
Direction buttons
Mute
Numeric buttons
Repeat A-B
Repeat
Audio
SubTitle
Angle
Program
PBC
Slow
Step
FF/FB
PREV/NEXT Skip
Zoom
Stop
Play/Pause
Setup
N/P
Display
Views of the Remote Control
Remote Control
Battery Installation
Connections
Connecting to a TV set
(TV or monitor with audio/video input)
NOTE:
1. Refer to the owner's manual of your TV as well.
2. Before connecting the DVD player to a TV set, be sure to turn the power off
and unplug both units from the wall outlet.
Audio/Video cable(Supplied)
To AUDIO OUT
To VIDEO OUT
To AUDIO/VIDEO
input
Clear
NOTE
The buttons of same descriptions on the main unit/remote control are of same functions.
Refer to the diagram. Open the battery compartment of the
remote control. Insert batteries, and then close the compart-
ment.
To use the remote control, point it at the remote sensor of
the unit and operate in the range of 5 meters and at angle
of 60 degrees.
Generally, the batteries last for about one year. Replace the
batteries if the remote control does not work.
Do not spill water on the remote control.
Do not use remote control for other equipments at the same
time.
Remove the batteries if the remote control will not be in use
for a long period of time.
NOTE
WARNING:
The battery used in this device may present a fire or chemical burn hazard if mistreated.
Do not recharge, disassemble, incinerate, or heat the batteries about 1000C (2120F).
Use of another battery may present a risk of fire or explosion. Dispose of used batteries.
Do not dispose of fire.
Keep batteries out of children's reach.
Connecting to an amplifier equipped with a Dolby Pro Logic Surround
Amplifier equipped with a Dolby Pro Logic Surround
To Coaxial Input
To Coaxial OUT
Coaxial cable (not supplied)
When connecting the equipment to a receiver equipped with
Dolby Digital, refer to the owner's manual.
N/P
TF-DVD5050
Connections
.7.
.8.
Connections
Power Connections (to Battery Pack)
Connecting to a Headphone
Be sure that your unit is at low volume level before
connecting the headphone.
Increase the volume gradually for your
comfortable listening.
CAUTION:
Hearing experts advise against the constant use
of personal stereos played at high volume.
Constant high volume use can lead to hearing loss.
If you experience ringing in the ears or hearing loss,
discontinue use and seek medical advise.
Power Connections (to AC Adapter)
**Do not connect the power cord until all other connections have been made.
AC adapter:
This AC adapter operates on
100-240V~~50/60Hz 2A Min
DC OUT: 9V
DC current: 2.0A Min
To Headphone jack
Headphone
To DC in jack
AC100-240V
Power is supplied through the provided appropriative power adapter, one end of which is connected
to the DC IN jack on the main unit, another to wall outlet with AC100-240V.
Note:
a. If you have difficulty inserting the plug, turn it over and reinsert it.
b. If the unit will not be in use for long periods of time, disconnect the plug from the outlet.
c. In order to prolong the operation life, the intervals of continuous power on should be not less
than 30s.
Note:
The battery can be recharged about 300 times without obvious performance drop.
The unit will not operate on battery power when the AC power cord is plugged into the AC socket.
Low Battery Detection: The unit will stop automatically and turn to STANDBY mode when voltage
reaches too low.
Power Connections (to DC Car Cord)
To the DC 9V In of main unit
To the DC Jack of Car
Plug the DC Car Cord to the DC in Jack for power supply.
Note:
a. Please do not plug it to the battery recharge jack.
b. The DC Car Cord is only for in car use.
Insert Battery
For initial use, we recommend it be charged for at least 4 hours.
a/ Push the battery door to arrow direction to open it
b/ insert the battery and then close the door by hand.
Charge Battery
To charge the battery, just leave it in its compartment and then power on the unit by AC adaptor.
Battery LED indicator lights red while battery is under charging and it will turn to green after the battery
is fully charged.
1.000
SCALE
(a) (b)
1.000
SCALE
Battery LED Indicator
