background image

Customer Assistance

Warranty

Introduction

Operation

10

Mode Functions

Operation

11

Set DCS Privacy Codes

To select a DCS privacy code:
1.

After selecting a channel, press the

Mode

button until the DCS icon appears and the
small numbers flash on the display
(01 through 83).

NOTE

If CTCSS is turned

on

at the channel

selected, the display will flash the
DCS icon and “OFF.” To switch from
CTCSS to DCS, press the

Channel Up

or

Channel Down

button while the

display is flashing “OFF.” The display
will then show the small numbers
flashing and you will then be able
to proceed to step 2.

2.

Press the

Channel Up

or

Channel Down

button to select a DCS privacy code. You can
hold the

Channel Up

or

Channel Down

button

for fast advance.

3.

When your desired DCS privacy code is
displayed, choose one of the following:

a.

Press the

Mode

button to enter the new

setting and proceed to other functions.

b.

Press the

Lock/Enter

button to enter the

new setting and return to

Standby

mode.

c.

Do not press any buttons for 15 seconds
to enter the new setting and return to

Standby

mode.

NOAA* All Hazards Radio Channels

You can use your microTALK

®

radio to listen to

NOAA All Hazards

Radio

channels transmitting in your area.

To listen to All Hazards Radio channels:
1.

Press the

Mode

button until the

WX

(All

Hazards Radio) icon, the currently selected All
Hazards Radio channel, and signal strength
are displayed.

2.

Use the

Channel Up

or

Channel Down

button

to change All Hazards Radio channels.

3. WX

(All Hazards Radio) icon will continue to

be displayed when All Hazards Radio is

on

.

Choose one of the following:

a.

Press the

Mode

button to proceed

to other functions.

b.

Press the

Lock/Enter

button to exit

All

Hazards Radio

channels mode and return

to

Standby

mode.

*National Oceanographic and Atmospheric Adminstration

Channel Buttons

DCS Privacy Code

Channel Buttons

Hazards Radio Icon

Mode Button

Mode Button

Содержание microTalk LI 7020 WX


















Отзывы: