background image

- 7 - 

deflectors and/or grass catchers, in place. 

12. Do not change the engine governor settings or over speed the engine. 

13. Before starting the engine disengage all blades and drive clutches. 

14. Keep your feet well away from the blade when starting the engine and in accordance with the 

instructions.   

15. Do not tilt the lawn mower when starting the engine and always start on a flat surface free from long 

grass. 

16. Caution: The lawnmower shall not be operated without either the entire grass catcher or self-closing 

discharge opening guard in place. 

17. Do not start the engine when standing in front of the discharge chute. 

18. Never put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. 

19. Always ensure the engine is fully switched off before picking up/carrying the Lawnmower. 

20. Stop the engine and disconnect the spark plug wire, make sure that all moving parts have come to a 

complete stop and, where a key is fitted remove the key, make sure engine has had time to cool. 

              - Before unclogging chute and clearing blockages. 

              - Before checking, cleaning or working on the lawn mower. 

      - After striking a foreign object. Inspect the lawnmower for damage and make repairs before 

        restarting.                                                                                                       

              - If the lawn mower starts to vibrate abnormally (check immediately). 

21. Stop the engine and disconnect the spark plug wire, make sure that all moving parts have come to a 

complete stop and, where a key is fitted remove the key, make sure engine is completely cooled. 

              - Whenever you leave the lawn mower. 

              - Before refueling. 

22. Reduce the throttle setting during engine shut down and, if the engine is provided with a shut-off valve, 

turn the fuel valve off at the conclusion of mowing. 

Maintenance and Storage 

1. Keep all nuts, bolts and screws tight to be sure the equipment is in a safe working condition.

 

2. Never store the equipment with petrol in the tank inside a building where fuel vapours can reach an 

open flame or spark or where the temperature is high. 

3. Before storage allow the engine to cool. When cooled, clean and undertake any maintenance. 

4. 

To  reduce  the  fire  hazard,  keep  the  engine,  silencer,  battery  compartment  and  petrol  storage  area                                                         

free of grass, leaves, or excessive grease. 

5. 

Check the grass catcher and deflector frequently for wear or deterioration. 

6.

  Replace  worn  or  damaged  parts  for  safety.  Genuine  parts  should  always  be  used  as  parts  of                                                 

inferior quality can damage the equipment and compromise safety. 

7. 

If the fuel tank has to be drained, this should be done outdoors. Always ensure engine is completely     

Содержание G46SHL-B1




























Отзывы: