Cobra CX50P3 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 78

Cobra CX50P3 Скачать руководство пользователя страница 55

55

CLUTCH WASHER STACKUPS:

Once the clutch is removed, and cool to touch, carefully put it into a vice and
remove the center shoulder bolt out of each clutch shoe. You WILL have to heat
the center hub again to remove the bolts. Once you get a bolt loosened,
carefully remove it with the shoe and observe the way the spring washers are
stacked. Clean the washers and bolt if you intend to reuse.

CAUTION:
You

should apply heat

to the arbor near the clutch bolt threads or you will very

likely break the Torx bit upon attempted removal.

The spring stacks in your Cobra clutch will contain 11 individual springs and flat
washer(s) configured as a 5 ½ stack. See figure 32. This clutch is designed such
that it reconfigured by the customer to achieve different clutch engagements ‘hits’
by changing washer counts and configurations.

CAUTION:
Generally reassemble the springs as you removed them from the engine or as
you received them from Cobra. If you are unsure call the Cobra Technical
Support Group 517 437 9100 and consult the experts.

5GX CLUTCH ASSEMBLY REFERENCE DRAWING

REF # PART #

DESCRIPTION

1

CAMU0009

Set of three shoes, springs, bolts, flat washers & nuts

2

CAMU0014

Set Of three springs, washers, bolts & nuts

Not Shown

CAMU0002

Complete assembled clutch

(Arbor, shoes and washer stacks)

Figure 32 Some configuration of clutch spring stack

. Each ‘spring’ stack contains multiple

springs (Belleville washers) - arranged into three, four, or five ‘flying saucers’, or turned away
against the flat washer(s). Shown is the 5 ½ stack..

Stack Total

Springs

Flying Saucers

or Cymbal

Pairs

Turned Away

or Dish

Stacked

Std. Flat

Washer(s)

HIT

5 ½

11

5

1

VARIED

HARD

4 11

4

3

VARIED

SOFTER

«
...
53
54
55
56
57
...
»

Содержание CX50P3















































































Отзывы:

Нет отзывов