manualshive.com logo in svg
background image

 

DISCLAIMER OF WARRANTY 

 

This motorcycle is sold “as is” with all faults, obvious or not.  There are no warranties 
expressed or implied, including any warranty of merchantability and warranty of fitness 
for any particular purpose.

 

 
 

WARNING 

 

THE COBRA CX50P3 IS A COMPETITION MODEL ONLY AND IS NOT 
MANUFACTURED FOR, NOR SHOULD IT BE USED ON PUBLIC STREETS, ROADS 
OR HIGHWAYS.  
 
THE USE OF THIS BIKE SHOULD BE LIMITED TO PARTICIPATION IN 
SANCTIONED COMPETITION EVENTS UPON A CLOSED COURSE BY A 
SUFFICIENTLY SKILLED RIDER AND SHOULD NOT BE USED FOR GENERAL 
OFF-ROAD RECREATIONAL RIDING.   
 
IMPROPER USE OF THIS MOTORCYCLE CAN CAUSE INJURY OR DEATH. 
 
THIS BIKE IS INTENDED FOR EXPERIENCED RACERS ONLY AND NOT FOR 
BEGINNERS. 
 
IT IS YOUR RESPONSIBILITY AS THE OWNER OF THIS COBRA MOTORCYCLE 
OR AS THE PARENT, OR LEGAL GUARDIAN OF THE OPERATOR, TO KEEP THIS 
COBRA MOTORCYCLE IN PROPER OPERATING CONDITION. 
 
THIS BIKE WAS DESIGNED FOR RIDERS THAT WEIGH LESS THAN 80 LBS WITH 
FULL RIDING GEAR AND SHOULD NOT BE OPERATED BY RIDERS THAT WEIGH 
MORE. 
 
BE SURE THAT THE RIDER ALWAYS WEARS ADEQUATE SAFETY GEAR 
EVERYTIME HE OR SHE RIDES THEIR COBRA MOTORCYCLE. 
 

 

IMPORTANT SAFETY NOTICE 

 

Failure to follow WARNING instructions could result in severe injury or death to 
the machine operator, a bystander, or a person inspecting or repairing the 
machine. 
 
CAUTION: 
A CAUTION indicates special precautions that must be taken to avoid damage to 
the machine. 
 

NOTE:  

A NOTE provides key information to make procedures easier or clearer. 

MCCL2017.0 

Содержание CX50P3















































































Отзывы: