8
|
USER MANUAL
| XXL-Rehab Shower Commode Tilt
Preparation
Before the system may be used, the battery must be
charged using the accompanying charger. It takes 5-8 hours
to fully charge a battery.
The yellow LED lights up when the charger is connected to
power. Place the battery in the charger by sliding it in and
rotating it until it is pulled into place by the magnets. The
green LED will flash at approx. 1 second intervals while the
battery is being charged. Once charging is complete the
green LED remains permanently lit. Remove the battery by
rotating it 90 degrees. It will then be ejected and be ready
for use.
Once the battery is fully charged, insert it into the controller.
Follow the same procedure as for the charger. If everything
is OK, the controller will simply sound a beep (3 seconds)
once the battery is in place. If the system has any faults, the
beep will be followed by 2 or 5 buzzer tones:
-
2 long buzzer tones:
The controller requires 0-point cali-
bration. See section about 0-point calibration below.
-
5 short buzzer tones:
The battery must be charged. See
above. It is not possible to operate the actuators.
The two fault notifications maybe sounded successively if
both faults are present.
When the battery requires recharging, transfer it to the char-
ger as described above. It is recommended that you keep an
extra battery on hand to avoid disruption to operation.
Always wait at least 2 seconds after the last actuator has
stopped moving before removing the battery. Otherwise
the controller may not have time to store the position and it
may be necessary to perform 0-point calibration as descri-
bed in section about 0-point calibration.
Normal operation
During normal operation the actuator is driven in an out
using the appropriate buttons on the remote control. Si-
tuations may arise which require a particular action. These
situations are described below.
Low battery level
If the battery level goes below a warning level while operating
the actuators, 3 short buzzer tones are sounded. This means
that the battery requires recharging, and the actuators can
therefore only be driven in one direction (normally in).
Flat battery
If the battery level goes below a minimum level while ope-
rating the actuators, 1 short buzzer tone is sounded. The
actuators will stop immediately and the controller will shut
down. The battery must be charged. You must wait at least 1
minute before inserting a new battery into the controller.
If you are using actuators with position feedback (hall
effect), you will need to perform 0-point calibration. See
section about 0-point calibration below.
Extreme battery load
The battery may become too hot if it is subject to extreme
load due to repeated operations in rapid succession, thereby
activating the battery’s safety thermostat. The controller will
shut down and the battery must be allowed to cool for at
least half an hour before being used again. You must wait
at least 1 minute before inserting a different battery into the
controller. If you are using actuators with position feedback
(hall effect), you will need to perform 0-point calibration.
See section about 0-point calibration below.
NB:
An alarm only sounds during operation of the actua-
tors. No alarm will sound while the system is inactive, even
if the battery is close to requiring recharging. It is therefore
recommended that you always keep a charged battery on
hand when using the system.
0-point calibration
If you use actuators with position feedback (hall effect), you
will need to perform 0-point calibration on the controller so
that the innermost position of the actuators can be recor-
ded. This must be done for all actuators which use position
feedback. The controller will sound 2 long buzzer tones
following the beep when the battery is inserted if 0-point
calibration is required.
It is also possible to initiate manual 0-point calibration by
holding in both buttons for the relevant actuator(s) for 12
seconds. The controller sounds a beep followed by 2 long
Instructions for battery and actuators
Battery, controller and
remote control
Battery mounted in charger
Battery mounted in the
controller – ready for use
