Cobalt Digital Inc BBG-1002-UDX-FS Скачать руководство пользователя | Manualshive

Страница: 105 / 110

background image

BBG-1002-UDX-FS-OM (V1.0)

BBG-1002-UDX-FS PRODUCT MANUAL

3-75

Operating Instructions

Troubleshooting

BBG-1002-UDX-FS Processing Error Troubleshooting

Table 3-4 provides BBG-1002-UDX-FS processing troubleshooting
information. If the BBG-1002-UDX-FS exhibits any of the symptoms listed
in Table 3-4, follow the troubleshooting instructions provided.

In the majority of cases, most errors are caused by simple errors where the
BBG-1002-UDX-FS is not appropriately set for the type of signal being
received by the device.

Note:

The error indications shown below are typical for the corresponding error con-
ditions listed.

Note:

Where errors are displayed on both the BBG-1002-UDX-FS and network
remote controls, the respective indicators and displays are individually
described in this section.

Table 3-4

Troubleshooting Processing Errors by Symptom

Symptom

Error/Condition

Corrective Action

BBG-1002 shows Unlocked
message in BBG-1002-UDX-FS
Info pane.

No video input present

Make certain intended video source is
connected to appropriate BBG-1002-UDX-FS
video input. Make certain BNC cable
connections are OK.

Ancillary data (closed captioning,
timecode) not transferred
through BBG-1002-UDX-FS

• Control(s) not enabled

• Make certain respective control is set to On or

Enabled (as appropriate).

• VANC line number conflict

between two or more
ancillary data items

• Make certain each ancillary data item to be

passed is assigned a unique line number (see
Ancillary Data Line Number Locations and
Ranges on page 3-9).

(QC only) Audio silence
event not detected or triggered
on

Holdoff set too long to detect
condition

The Trigger Holdoff controls on the Audio
Detect Events tab allow ignoring silence events
unless the event duration exceeds the holdoff
setting. Make certain holdoff is set sufficiently
low to detect events as desired.

Audio not processed or passed

Enable control not turned on

On Output Audio Routing/Controls tab, Audio
Group Enable control for group 1 thru 4 must be
turned on for sources to be embedded into
respective embedded channel groups.

Excessive or nuisance input
signal quality events in log or
Card State status display

Holdoff periods are too brief (or
threshold set too high)

If holdoff periods are too brief (or threshold set
too sensitive), nuisance alarms may be
generated during transitions to and from
programs and interstitials, as well as during
certain content.

Selected upgrade firmware will
not upload

Automatic reboot after upgrade
turned off

Card Presets > Automatically Reboot After
Upgrade box unchecked. Either reboot the
device manually, or leave this box checked to
allow automatic reboot to engage an upgrade
upon selecting the upgrade.

«
...
103
104
105
106
107
...
»

Содержание BBG-1002-UDX-FS















































































































Отзывы:

Нет отзывов

Похожие инструкции для BBG-1002-UDX-FS

Бренд: Bang & Olufsen Страницы: 44

blueplanet 3.0 NX1 M2

Бренд: Kaco Страницы: 33

Бренд: Kaco Страницы: 15

blueplanet 110 TL3

Бренд: Kaco Страницы: 119

LaCinema Black RECORD

Бренд: LaCie Страницы: 5

Бренд: Omega Engineering Страницы: 10

Бренд: TDT Страницы: 2

Бренд: Teac Страницы: 23

Бренд: APS Страницы: 70

AudioImage SX9100

Бренд: invotel Страницы: 2

Бренд: ViewSonic Страницы: 26

NMP-600 - Network Media Player Connects

Бренд: ViewSonic Страницы: 2

Бренд: Goobay Страницы: 8

Бренд: Lindy Страницы: 14

Бренд: Badger Power Electronics Страницы: 29

Бренд: G-Power America Страницы: 55

Бренд: Cobalt Digital Inc Страницы: 126

Бренд: Stealth Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды