manualshive.com logo in svg

Cobalt Digital Inc 9922-FS, Руководство по эксплуатации продукта, Страница: 80 / 118

Поделиться
Скачать
Cobalt Digital Inc 9922-FS Скачать руководство пользователя страница 80

3

9922-FS Function Menu List and Descriptions

3-38

9922-FS PRODUCT MANUAL

9922FS-OM (V1.5)

Provides an audio crosspoint allowing the audio source 
selection for each analog audio output channel. Also 
provides Gain, Phase Invert, and Muting controls and 
peak level meters for each output channel.

• Analog Output Channel Source

Using the Source drop-down list, selects the audio input source to be 
routed to the corresponding analog audio output channel from the 
following choices:

• Card Audio Bus Ch 1 thru Ch 16

• Built-in Tone generators Tone n

(-20 dBFS level tone generators with n being frequencies of 100, 200, 
300, 400, 500, 600, 700, 800, 900, 1k, 2k, 4k, 6k, 8k, 12k, and 16k)

• Flex Bus A thru P mixer sum node outputs

•

Audio LTC 

• Downmixer L

• Downmixer R

• Channel Mute/Phase Invert/Gain Controls 

and Peak Level Display

Provides Mute and phase Invert channel controls, as well as peak level 
meter for each output channel. (Meter shows level as affected by Level 
control.)

Gain controls allow relative gain (in dB) control for each corresponding 
destination analog audio out channel.

(-80 to +20 dB range in 1.0 dB steps; unity = 0 dB)

Table 3-2

9922-FS Function Menu List — continued

Содержание 9922-FS























































































































Отзывы:

Нет отзывов