Cobalt Digital Inc 276 bowrider Скачать руководство пользователя | Manualshive

Страница: 126 / 132

background image

7

-

2

276 Owner’s Manual

COBALT

276

BOWRIDER

S

ECTION

7

Starting Engines

• Operate bilge blowers for at least four minutes

before starting the engines or generator.

• Turn battery selector switches to ON.

• Attach lanyard to the ignition safety switch and

the operator.

• Make sure both shift levers are in the

NEUTRAL position.

• Move both throttle levers to the IDLE position.

• Start both engines. Operate the engines at

1000 RPM (gas engines), 1400 RPM (diesel
engines) and check if oil pressure is within
specified range. Make sure the water pressure
gauges start to indicate pressure in 15
seconds or less after starting. If not, shut off the
engines and verify the engines are getting
cooling water.

After engines are warmed up, verify water
temperature is within its specified range.

Casting Off

• Allow enough room between the boat and the

dock to swing the boat away from the dock.

• Retrieve all mooring lines and fenders.

• Proceed slowly and sound a long blast to alert

other boaters you are leaving.

During Operation

• Check gauges frequently for signs of abnormal

operation.

• Check for excessive vibration.

• Monitor your fuel supply.

• Verify charging of the batteries.

Returning to Port

• Come to a stop a short distance from the dock,

then proceed slowly.

• Have your fenders, mooring lines and the crew

ready.

Stopping the Engines

• Slowly bring the throttle levers to the IDLE

position.

• Move the shift levers to the NEUTRAL position.

• Turn the ignition keys to the OFF position.

After Boating

• Turn off your navigational lights, leave the

anchor light on, if necessary.

• Check the bilge for gas fumes and water.

Operate the blower and bilge pump, if
necessary.

• Fill fuel tanks to prevent moisture due to

condensation.

• To prevent marine growth from accumulating

on the hydraulic cylinder shafts, make sure trim
tabs are up and propulsion unit drives are in the
full IN position.

• Lock ignition key switch and remove the

ignition keys.

• Stow and secure all equipment.

• Pump bilges dry with manual switch.

• Close all water inlet seacocks.

• If possible, inspect the hull and propellers for

damage.

• Check for fuel, oil and water leaks.

• Clean any spills, stains or moisture from the

boat. Inspect sea strainers.

• Turn battery selector switches to the OFF

position.

• Turn breakers on electrical panel to the OFF

position.

• Remove any food, garbage and wet gear from

the boat.

• Secure lockers, hatches and canvas as

equipped.

«
...
124
125
126
127
128
...
»

Содержание 276 bowrider





































































































































Отзывы:

Нет отзывов

Похожие инструкции для 276 bowrider

Бренд: 3d Страницы: 17

Бренд: PURSUIT Страницы: 136

Бренд: Cobalt Digital Inc Страницы: 134

Бренд: Sea-doo Страницы: 96

Бренд: Sea-doo Страницы: 92

Бренд: Sea-doo Страницы: 132

Бренд: Sea-doo Страницы: 148

Coastal Explorer 191

Бренд: Grady-White Boats Страницы: 74

Бренд: RIOT Страницы: 7

Бренд: Pelican Страницы: 3

2909 Walkaround

Бренд: Trophy Страницы: 72

Бренд: Tartan Страницы: 72

Бренд: Carp Madness Страницы: 23

Бренд: Robalo Страницы: 90

2008 Center Console

Бренд: Robalo Страницы: 106

Бренд: Robalo Страницы: 143

Бренд: Inflatable Sport Boats Страницы: 16

Бренд: iSport Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды