Coast Spas TRADITIONAL APEX, Руководство пользователя

Страница: 29 / 66

OWNER’S MANUAL 2021
29
How to adjust the Filtration
Press and release the “Menu” button until “FLTR” 1 or 2 appear on
the screen. Press and release the “Up” or “Down” button to enter
the menu, “BEGN” should appear. Press and release the “Up” or
“Down” button to set the start time (Option 1) or Press and release
the “Menu” button to set the duration (Option 2).
Pressing and releasing the “Menu” Button again during the
“RUN”-”HRS” will display which filter cycle is being set and the end
time. Press and release the “Menu” once more to save the
settings.
Option 1:
Setting the Start Time With “BEGN on the screen press
and release the “Up” or “Down” button, use the “Up” or “Down”
buttons to adjust the starting hour. When satisfied press the
“Menu” to proceed to the Minutes. Use the “Up” or “Down” buttons
to adjust the starting Minutes. When complete press the “Menu”
button to save the starting time.
Option 2: Setting the Duration With “BEGN on the screen press
and release the “Up” or “Down” button to set the starting time
(Option 1, please see above) or press the “Menu” button to
proceed to “RUN”-”HRS”. Use the “Up” or “Down” buttons to adjust
the hours of duration. Press the “Menu” button to start the minutes.
Use the “Up” or “Down” buttons to adjust the duration minutes.
When complete press the “Menu” button to save the duration time.
Filter Cycle 2 - Optional Filtration
Filter Cycle 2 is OFF by default. It is possible to overlap Filter
Cycle 1 and Filter Cycle 2, which will shorten overall filtration by
the overlap amount.
Purge Cycles
In order to maintain sanitary conditions, secondary Pumps and/ or
a Blower will purge water from their respective plumbing by
running briefly at the beginning of each filter cycle. If Filter Cycle 1
is set for 24 hours, enabling Filter Cycle 2 will initiate a purge when
Filter Cycle 2 is programmed to begin.
Additional Information
Preferences
Press and release the “Menu” button until “PREF” appears. Press
and release the “Up” or “Down” button to enter the Preferences
menu. Use the “Menu” button to scroll through the options (listed
ahead) and the “Up” or “Down” buttons to enter that section. While
in a section use the “Up” or “Down” buttons to toggle the options
and the “Menu” button set each option in the memory.
F/C (Temp Display)
Change the temperature between Fahrenheit and Celsius.
12/24 (Time Display)
Change the clock between 12 hr and 24 hr display.
RE-MIN-DERS (Reminders)
Turn the display of reminder messages (like “Clean Filter”) On
or Off. Note: Reminders continue to run in the background
even when not displayed. So turning the display of Reminders
On or Off does not reset any Reminder counts.
CLN-UP (Cleanup)
Cleanup Cycle Duration is not always enabled, so it may not
appear. When it is available, set the length of time Pump 1 will
run after each use. 0-4 hours are available.
M8
(This message may not appear on all systems.) On systems
that have M8, it is enabled by default. It can be disabled
(or re-enabled) here. M8 reduces polling intervals when the
water temperature in the spa is steady.
DOL-PHIN-AD-DRES (Dolphin II and Dolphin III)
Applies to RF Dolphin only. (This message may not appear
depending on the configuration) When set to 0, no addressing is
used. Use this setting for a Dolphin Remote which is factory set
for no address by default. When set between 1 and 7, the
number is the address. (See the Dolphin manual for details.)
Utilities and Information
Press and release the “Menu” button until “UTIL” appears. Press
and release the “Up” or “Down” button to enter the Preferences
menu. Use the “Menu” button to scroll through the options (listed
ahead) and the “Up” or “Down” buttons to enter that section.
While in a section use the “Up” or “Down” buttons to toggle the
options and the “Menu” button set each option in the memory.
INFO (System Information sub-menu)
The System Information Menu displays various settings and
identification of the particular system.
SSID (Software ID)
Displays the software ID number for the System. MODL
(System Model) Displays the Model Number of the System.
SETP (Current Setup) Displays the currently selected
Configuration Setup Number.
Heater Voltage (Feature not used on CE rated systems)
Displays the operating voltage configured for the heater.
Heater Wattage as Configured in Software (CE Systems
Only)
Displays a heater kilowatt rating as programmed into the control
system software (1-3 or 3-6).
TRADITIONAL SPAS