Coast Spas Classic Series, Руководство пользователя

Страница: 31 / 32

31
IN.CLEAR—GETTING STARTED
See video: http://www.inclear.ca/inclearstartupprocedure
For more information: http://www.inclear.ca/inclearwater
1. CLEAN THE SPA
It's important to completely clean the spa to remove all residues
accumulated on the surface and inside or around the jet area.
After draining the spa, use spa cleaning products only. House-
hold cleaners contain additives such as phosphates which may
affect the bromine production.
2. TDS (TOTAL DISSOLVED SOLIDS) CHECK
check the TDS (Total Dissolved Solids) of the water you'll use to
fill the spa. Verifying the TDS range can be done by your spa
selling dealer. The TDS range should be within 50 and 400
PPM. When you're certain the water is within the proper TDS
range, fill your spa. If the TDS is higher than 500 PPM, ask your
spa dealer for additional information to help reduce initial TDS.
DO NOT use water from a "Salt Water Softener" system. Make
sure there is adequate flow and that no airlocks are trapped in
the unit's plumbing. If airlocks are formed, start the pump and
follow the instructions in the owner’s manual.
3. ADJUST WATER CHEMISTRY IN THE SPA
Proper chemical maintenance of a spa is essential for the health
of bathers. Maintaining the quality of the spa water within these
specified values will enhance your enjoyment of the spa and
prolong the life of the In.Clear system.
For best results, adjust to the following water chemistry parame-
ters. Check these parameters periodically.
Calcium hardness
(TH): between 150 and 200 PPM Total Alkalinity: between
100 and 120 PPM pH: between 7.2 and 7.8
Water chemistry should be balanced before adding sodium bro-
mide into the water. It's essential that the water chemistry pa-
rameters are within the proposed range to obtain optimal sys-
tem performance. vHigh Calcium Hardness may lead to faster
calcification of the electrolytic plates.
4. ADD SODIUM BROMIDE (SUCH AS BROMICHARGE)
Water temperature between 32° and 38° C (90° and 100° F)
helps dissolve sodium bromide and facilitates the adjustment of
the maintenance level. Start the pump on high speed to allow
water to circulate and slowly add sodium bromide uniformly in
the spa by simply pouring it from the container. Metric Calcula-
tion: Add 0.143 kg of sodium bromide which has a guarantee of
at least a 98% active ingredient, such as BromiCharge, per 100
L of water to attain 1400 ppm TDS value (Total Dissolved Sol-
ids). Example, if your spa holds 1200 L of water, add 1.72 kg of
sodium bromide (12 X 0.143 kg). Imperial Calculation: Add sodi-
um bromide which has a guarantee of at least a 98% active in-
gredient, such as BromiCharge per 100 US gallons of water.
Example, if your spa holds 300 US gallons of water, add 3.6 lbs
of sodium bromide (3 X 1.2 lb).
Note: Your selling dealer can tell you how much water your
spa holds (in liters or gallons).
MAINTENANCE MODE
Maintenance Mode keeps the bromine bank levels at
a stable and acceptable range when the spa is not being
used. Maintenance mode is the “everyday” mode
and is automatically ON when the system is activated.
Press and hold the Program key for 2 seconds to change the
maintenance mode level.
Use the Up and Down keys to adjust the maintenance level,
ranges from 1 to 50.
Finding and setting the right maintenance level will keep the re-
sidual bromide level between 3 and 5 PPM (the recommended
range). Once the proper maintenance level is determined, keep
the same setting unless the spa conditions change (change in
water temperature, spa location etc.).
BOOST MODE
The Boost Mode should be activated every time you use your
spa. Boost mode increases the bromine generation rate to attack
pollutants in the water and helps rebuild the necessary residual
bromine in the water after each use of the spa.

If water quality is not good after use, only boost level should
be adjusted, not the maintenance level.

Press the Boost key once while in maintenance mode to
start a boost, or to adjust boost settings.

Use the Up and Down keys to adjust the boost level, ranges
from 1 to 8.
Note: Boost levels depend on the number of bathers using
the spa. We recommend you validate the Boost level after each
use to determine the ideal boost level for all numbers of bathers.
OWNER’S MANUAL
2020