manualshive.com logo in svg

CNC QB2, Руководство пользователя

Поделиться
Скачать
CNC QB2 Скачать руководство пользователя страница 18

 

Page 18 

 

1.

 

Raise your spindle high enough so that you can fit the laser to the side of the Right-
hand side of your spindle bracket. Use the 2 bolts provided to secure it to the 
bracket. We always recommend fitting it to the right-hand side so you can still 
safely home when the laser is attached. 

POWER OFF YOUR MACHINE 

then connect 

to white laser plug to the top of the laser.

 

 

2.

 

Once firmly attached you can power up the machine and connect to it in 
Commander remembering that you will need to re-home it before being able to jog 
any axis. Use the alloy spacer provided with your laser to set the correct focal point 
of the laser. To do this, position the spacer under the laser head and carefully 
lower your Z axis until the brass laser head is just clearing the alloy spacer. Take 
care not to damage the laser by crashing into the spacer! 

 

  

 

We recommend following our video guide here for using your laser: 

https://www.youtube.com/watch?v=8Syf86xmeZs&t

 

 

Some key laser points! 

Always remove your laser when using your spindle and never leave 
your machine unattended when using it. Also ensure you have 
adequate extraction to your work area as laser jobs can produce 
harmful fumes when operating. 

 

Содержание QB2






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды