CMP 25514-00X-000 Скачать руководство пользователя страница 6

6

C. INSTALLATION & MAINTENANCE

VINYL INSTALLATION: 

a.  Finish pool surface so that it is completely level with the sump body and cover. Pool finish should not exceed the top of 

the sump.

b.  Place gasket on sump body, making sure holes in gasket align with holes in sump flange (a very light application of 

silicone will help hold the gasket in place).

c.  Install liner before proceeding to next step. Follow pool manufacturer’s instructions for proper vinyl liner installations.

d.  Align second gasket and vinyl ring outside the vinyl liner. Pierce vinyl liner through vinyl ring holes one at a time before 

inserting screws. Screws must go through ring, gasket, liner, second gasket and into sump. Verify that the vinyl ring is 

properly tightened with the stainless steel screws in brass inserts to 24in-lbs.

e.  Cut out liner along inside edge of vinyl ring.

f.  When any SOFA component is held in place by the interior finish of the pool, that surface shall be free of deterioration 

and voids.

g.  Attach cover/grate with the supplied screws. Verify that the suction cover is properly tightened with the #8 316 stainless 

steel screw in brass inserts to 14in-lbs. DO NOT over-torque the cover screw. Excessive torque can cause premature failure 

of threads or damage to suction fitting increasing risk of entrapment. Start install of screws by hand to ensure proper 

thread engagement and to prevent cross threading. DO NOT USE POWER TOOLS TO INSTALL FASTENERS. 

SOFA components and fastener receptacles shall be clean and free of debris or obstructions during installation of cover/grate 

and fasteners. The use of adhesives or other attachment methods that prevent access to suction piping or SOFA components 

requiring periodic servicing is prohibited.  Hand-check cover/grate for snugness to the sump/ frame after installation. 

MIN 3 FT OR DIFFERENT PLANES

Gunite/

Shotcrete

Earth/

Substrate

Plaster/Pool Finish

Threaded Plug

IMAGE 1 - INSTALLATION - BOTTOM PORT

SIDE PORT

VINYL LINER

Threaded Plug

Vinyl

Liner

Gaskets

Install Ring

IMAGE 2  - ALTERNATE INSTALLATIONS

Содержание 25514-00X-000













Отзывы: